Question about 1997 Chevrolet Tahoe

1 Answer

Door unlock i left my keys in the ignition,with my doors locked,8(,,,,,,,,, and some one broke into my tahoe about 1 year ago,,and i noticed that they stuck a screw driver under the handle and popped the door open... i tried but no luck,,can you help me!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 373 Answers

Hi...
You can open By the handle.
But you will need desengage the little bar at the Lock cylinder.
and maybe you can damage the cylinder or handle.
If you have Aftermarket Alarm on your car.
Try to open de hood Pulling the hood realese cable.
From the grill.

But if you don't have aftermarket alarm.
Get a Flat screw driver, and try to insert between the door and body At the upper right corner of the door. Driver side.
If your Radio Anntena is Solid and you can remove easy.
Remove and Insert Beside of the screw driver and PUSH the UNLOCK buttom.

Ok.. I hope this help on your problem...
Thank you for use fixya..

Posted on Sep 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Program key fob


  1. Close all vehicle doors.
  2. Insert the key into the ignition.
  3. Hold down the power UNLOCK button on the driver's door panel-continue to hold down until instructed to release in step 9.
  4. Perform steps 5 through 8 in fairly rapid succession.
  5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
  6. Turn the ignition switch to the OFF position.
  7. Turn the ignition switch to the ON position.
  8. Turn the ignition switch to the OFF position.
  9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
  10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
  11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
  12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

Mar 12, 2015 | 2002 Chevrolet Chevrolet Tahoe

1 Answer

Having trouble with keyless remote control on 1993 lexus es300. Replace battery on remote- still not openning doors. Help Please!


Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Jan 02, 2013 | Cars & Trucks

1 Answer

Need help programing my keyless remote for a 2000 alero. This is what is on the back, GM/UTA 25665575, FCC ID. KOBUT1BT,Canada 1983 101 393 It has four buttons top two are left pic of lock, Right pic of...


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.



Thank you for using Fixya and good luck

Mar 17, 2010 | 2000 Oldsmobile Alero

1 Answer

Lost working keys extra will unlock but does not start how do i program extra key to start car


On 2002 model try the following:
1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.


from ProgramyourRemote

Jul 04, 2009 | 2002 Chevrolet Tahoe

1 Answer

How to program key fob. I have the fobs.


Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck

Jun 25, 2009 | 2002 Chevrolet Tahoe

1 Answer

Need to re-program 2000 Chev.C3500 key fob need help


1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Jun 09, 2009 | 1999 Chevrolet Tahoe

1 Answer

Program a new key fob for a 2002 chevy tahoe


1. Close all vehicle doors.



2. Insert the key into the ignition.


3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.



4. Perform steps 5 through 8 in fairly rapid succession.


5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).



6. Turn the ignition switch to the OFF position.


7. Turn the ignition switch to the ON position.


8. Turn the ignition switch to the OFF position.


9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.



10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.



11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).



12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.




Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 27, 2009 | 2001 Chevrolet Blazer

1 Answer

Remote entry key.


You may have lost programming in the remote.
Here are the instruction to program it

1. Confirm that all doors are closed and the ignition key is NOT in the ignition cylinder.
2. Open the driver's door and within 10 seconds insert the key in the ignition.
3. Now, within 10 seconds remove the key from the ignition.
4. Within the next 20 seconds, push and release the driver's door switch 3 times. This is the switch near the door strike plate which turns on the inside light and indicates that the door is open.
5. Within 10 seconds, insert the key in the ignition.
6. Now, within 10 seconds remove the key from the ignition.
7. Within the next 20 seconds, press and hold both the LOCK and UNLOCK buttons on the transmitter. Hold both for at least 5 seconds. All the doors will lock or unlock to confirm that procedure was done properly.
8. Within the next 5 seconds after step 7 was complete, press either the LOCK or UNLOCK button to confirm that this process has been properly done. Now, the transmitter has been programmed.
9. Repeat steps 1 to 8 for additional transmitters.
10. Operate each transmitter to verify the programming.

Sep 04, 2008 | 2004 Suzuki Verona

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

2 Answers

Keyless entry remote


Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks.

Jun 20, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
1997 Chevrolet Tahoe Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...