Question about Dodge Ram 1500

1 Answer

My truck keeps messing up my hanger bering - Ram 1500 Dodge Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 421 Answers

Pull your drive shaft out and have it rebalanced at a reputable drive shaft rebuilder such as levine automotive also check your rear trans mount and u-joints please rate -jeff

Posted on Sep 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace main bering


You can't just replace the main bearing, it will just burn out again, the engine must be removed and a new or re-man crankshaft fitted.

Jun 14, 2012 | Mitsubishi Pajero Cars & Trucks

1 Answer

How to pop the hood when the cable is messed up under the hood?


Look and find the end may be through the grill in the centre and bend a wire coat hanger to a hook see if you can give it a tug

Oct 20, 2010 | 1996 Buick LeSabre

1 Answer

FRONT WHEEL BEARING ON 2005 MAZDA 3 ARE THEY PRESSED IN?


2005 mazda 3 front wheel bering left side are they pressed in and tools needed 2 replace bering

Sep 05, 2010 | 2005 Mazda 3

1 Answer

Tailpipe is hanging very low


Hi. Under or near the tailpipe, there are rubber and sometimes steel hangers that are placed onto the sides of the pipe structure. These move with the assembly to provide little flexibility during travel. These hangers also are there to keep the pipe/muffler assembly from dragging or hanging to low. When the hanger assembly becomes unstable or damaged, it will allow the tail pipe assembly to hang low or sometimes drag the ground when you hit a bump. The necessary actions are to raise the vehicle high so that you can inspect the exhaust tail pipe assembly for broken hangers or steel bracing devices. replace any rubber hangers that may be snapped or missing form their respective locations. If you are uncomfortable with raising the vehicle, i would take the unit to a local muffler/exhaust shop for the inspection.

Aug 25, 2010 | 2003 GMC Yukon Denali

1 Answer

How to get to fuel pump


take the gas tank down. watch for special clips on the fuel lines, might have to move exhaust pipe or hangers to make room to drop down. This will be a mess with a full tank!

Feb 19, 2010 | 1994 Mercury Cougar

1 Answer

Rear whheel bering repair


need to find rear wheel bearing isuzu bighorn 3.1 (*** import)

Oct 28, 2009 | 1985 Isuzu Trooper

1 Answer

Replace rotor


when you take the front wheels off you will see a silver center cap in the middle of the hub take a flat heat screw driver a gently pry the cap off (don't worry if you mame it alittle) there will be a cotter pin a nut and a washer then you outter bering take them all off then the rotor will come off the inner bering is still in the rotor being held by the grease seal pry the old grease seal off and remove the bering. check berings for wear like ruff spots. make sure you buy a new grease seal for the rotor. reverse removal procedure re pack berings with fresh grease inner first place bering in the rotor put seal in place will need to tap it in carefully when putting the nut back on tighten untill snug not tight check for specs if you want i usually make it snug then 1 more turn do not over tighten and you will be good

Apr 07, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Weird thing going on w/ the gas pedal on a '89 camry


have the exhaust hangers checked, it is very much possible your exhaust is loose and that is what your feeling.

Oct 30, 2008 | 1989 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...