Question about 1999 Chevrolet Malibu

1 Answer


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,039 Answers

If you have no leak our master cylinder is defective good luck pierre

Posted on Sep 05, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

8 Answers

The brake pedal continue to slowly go down when the brake is applied. 2008 Mazda 3 2.3L

There may be air in brake lines. While changing pads probably it got air from oil cap to inside. I assume that i was opened while putting new pads. You should flush brake fluid first. It should fix the problem

Oct 24, 2017 | Mazda Cars & Trucks

4 Answers

Brakes are spongey been to dealer and they bleed system etc and made no difference . Now they are saying that is normal

year make model?

since you're seeing a dealership, i'm guessing it's still under warranty? if it's a new car, don't take no for an answer and go to another dealership

if this is an older car, goto an independent shop instead & see what they find

Apr 04, 2015 | Cars & Trucks

1 Answer

No break pedal

Have you checked the thing under the brake pedal? I can't recall what it is, a regulator or tensioner or something?

Sep 30, 2017 | 1993 Chevrolet S-10

2 Answers

1999 buick century brake pedal goes to floor-put new master cylinder on and blead both brake lines and master cylinder and pedal still goes to floor

Sounds like you may have a hydraulic leak somewhere. Check the rear wheel cylinders and front brake hoses going to the calipers.

Jan 26, 2012 | 1999 Buick Century

1 Answer

Brake pedal goes to floor -i put a new master cylinder on it and blead the lines and cylinder an still go to the floor

To bleed the brakes on this year and model requires a special tool that holds open the pressure valves in the active ABS system, there is no work around. Any brake shop or tire shop that does brake work can do this bleeding, I see this question all the time.

Jan 26, 2012 | 1999 Buick Century

1 Answer

I have a 96 ford explorer xlt 4wd with ABS. When I bought it it had a broken back break line. I replaced the line blead the breaks and the breaks are spongy. I googled the issuse and found out it could be...

Check your parking brake. if it goes down to the floor or does not hold, then your back brakes needs adjusted. bad master cylinders bleed off slowly to the floor while pushing on the brake pedal. If you need assistance on adjusting let me know.

Nov 09, 2010 | 1996 Ford Explorer

1 Answer

I have a 96 silverado with abs, a friend owed me some money so i told him to put new front brake pads and get the front rotors and rear drums turned, he finshed the job and called me and said my brakes are...

PRe bleed the master cylinder, using a kit that hooks up to the brake lines connection and the other end goes into the fluid reservoir. Bleed until no bubbles. then reinstall brake lines, one at a time, and then continue bleeding the system. DO NOT let the fluid run low in M/C or start all over again. Kit can be purchased at after market parts stores.

Oct 09, 2010 | Chevrolet 1500 Cars & Trucks

2 Answers

97 ford e350 brake pedal goes to the floor...

are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

1 Answer

94 4runner brake pressure.

did you possibly replace brake lines with standard instead of metric lines.The standard lines will fit but you will not get pressure back

Jul 20, 2008 | 1994 Toyota 4Runner

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77947 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides