If its the entire lense you need out then the grill is easy it consits of only a few bolts there are four right ubove the radiator one the grill is off there are bolt (10m i think) that hold the lense if im not mistakin the plastic wheely things are for positioning lights also try autohausaz.com has all the parts that you will need at least 50% off or
better. try them out i only buy though them and love them. hope this
works for you.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Turn off your Cadillac CTS and
look below the front grille for the bottom pins that hold it in place.
Push these pins inward to disengage them.
Open the hood. Look for the pins
that hold the grille in place on the engine compartment side. Push in
these pins. Pull the grille off the front of the Cadillac CTS.
Remove the side pins from the
CTS fender on the side that has the headlight you wish to replace. Pull
the side fender away from the vehicle to prepare for removing the headlight.
Remove the three bolts on the top and rear of the headlight.
Disconnect the wiring harness from the back of the headlight.
Push or pull the headlight
through the front of the Cadillac CTS and set it aside. This part may
require a lot of force if the headlight is stuck.
Insert the new headlight along
the runners upon which the previous headlight sat, and attach the wiring
harness. Reinstall the three bolts you removed earlier, as well as the
side finder and the grille.
you might need to move the air filter box to do this.
The bulb and its wiring is on the back of the headlight. Twist the clip to remove it from the headlamp housing, pull the bulb out and replace it, then reinstall the bulb into the housing. If you need to replace the whole headlight and not just bulb you'll need to remove the grille by unscrewing 4 screws on the top side of the grill Rotate the grill toward the front to release from the clips holding it in place. There are 2 screws on the inboard area of the headlamp. Remove these two screws and the lamp will come out. Now you can replace the lamps or the unit.
Sounds like you are right own...to change each bulb...you need to remove the chrome grill from the front center...be sure to pry up the clips carefully so not to break the trim bar...then each headlight assembly is removable with 3 10 mm bolts...do not touch your exposed fingers on the new bulbs...yes the low/high bulb is one unit...that is why I believe it is just your bulbs...about $11. each...Hope this helps.
Go to www.trailvoy and search the forums for change trailblazer headlight. Basically there are two ways, I will abbreviate. 1. Contort your hands to pull of the rubber caps - on the passenger side you will have to remove the air filter box. 2. remove the grill and pull out the entire headlight assemblies. I have done it both ways. For just headlights I suggest method 1. For turn signals, etc you will need to use method 2.
FACE THE VEHICLE SO THAT BATTERY IS ON YOUR RIGHT; 2.REMOVE THE BLACK PLASTIC PIECE THAT RUNS OVER RADIATOR BETWEEN HOOD LATCH AND FAN. IT IS ABOUT 53 1/2" LONG AND HOLDS THE HOOD PROP CLIP. (3 PLASTIC PUSH RETAINERS & 2 SHEET METAL SCREWS); 3.REMOVE THE GRILL ASSEMBLY UNDERNEATH THE PIECE IN STEP 2 BY PUSHING DOWN FIRMLY ON 4 RETAINER CLIPS WHICH RUN ALONG THE TOP. USE A WIDE SLOT SCREWDRIVER. PULL UP GENTLY ON GRILL ASSEMBLY. IT WILL POP OUT. THE GRILL ASSEMBLY EXTENDS UNDER EACH HEADLIGHT ASSEMBLY (HA) AND IT DISPLAYS THE CHEVROLET LOGO IN THE MIDDLE. MY GRILL ASSEMBLY POPPED OUT EASILY AND ALL THE OTHER RETAINER CLIPS ON THE BOTTOM AND BENEATH AND TO THE SIDE OF HA WERE AUTOMATICALLY RELEASED WITHOUT ANY FUSS; 4.ON TOP OF HA SEE ONE TAB (ABOUT 1" LONG)ON THE RIGHT SIDE AND ONE ON THE LEFT (THE ONE ON L IS CLOSER TO THE FENDER); 5.PULLUPWARDDIRECTION ON TABS. THEY WILL SLIDE UPWARD A COUPLE OF INCHES AND WILL RELEASE THE HA WHICH YOU CAN THEN PULL OUT TOWARDS YOU; 6.AT BACK OF THE HA, REMOVE 2 ROUND RUBBER CAPS (ABOUT 4" IN DIAMETER)--ONE FOR LOW BEAM--ONE FOR HIGH. REVEAL BULBS. UNSNAP THE WIRE HARNESS FROM BULB BASE AND TURN BULB 1/4 TURN CLOCKWISE (REMEMBER YOU ARE FACING THE TRUCK) 7.REPLACE BULB(S). #9006 BULB IS GRAY-BASE, FOR HIGH BEAM ON OUTSIDE. #9005 IS BLACK-BASE, LOW BEAM TO INSIDE OF HIGH BEAM. CHANGING HIGH AND LOW AND REASSEMBLY TOOK ABOUT HALF HOUR. GOOD LUCK.
ALTERNATIVE: IF YOU ARE REPLACING THE PASSENGERSIDE HEADLIGHT JUST REMOVE THE AIR FILTER COVER AND PULL PLUG OUR FROM BEHIND HEADLIGHT AND REPLACE. BE CAREFUL HANDLING LIGHT BULB. TO CHANGE THE ONE ON THE DRIVER'S SIDE JUST REACH IN FRONT OF THE BATTERY TO ACCESS THE PLUG AND HEADLILGHT. TOOK ABOUT 5 MINUTES. ENJOY YOU TRAILBLAZER, GREAT TRUCK.
Step 1 - Raise the hood and remove the 4 push-in retainers that go along the top of the front grille. These are each two part retainers - remove both parts by prying with a small screwdriver. Nothing comes off here - this just makes the grille loose for maneuvering the headlight assembly around to get it in and out. Step 2 - Remove the "bow tie" trim piece that runs from headlight to headlight thru the middle of the front grille - it is cheap plastic so do this carefully (mine looks like chrome with the Chevy 'bow tie' in the center). To do this, use a flat-bladed screwdriver and a rag (to protect the headlight). This trim part comes off - I started at the driver's side and work toward the passenger side. Place the rag below the trim on the headlight. Carefully pry up on the trim piece with the screwdriver and work the trim with your fingers until it pops out of the headlight assembly catch. There are lock tabs on both the top and bottom of this trim piece when you get to the grille area. Work your way down the trim piece by prying wherever you locate a tab and protecting with the rag as you go until the "bow tie" trim piece comes off. The headlight assembly catches are the tightest. Set it off to the side so you don't step on it or scratch it. Step 3 - Unbolt the light assembly. There are two hex-headed screws on top and one 10MM down inside (towards the center of the car). Remove these 3 bolts. Step 4 - Remove the assembly - There are 2 guide tabs in the lower outside part of the light assembly (opposite the 10MM screw). Wiggle the assembly while pulling out (forward). When the tabs clear, lift up on the headlight and it should be easy to work the rest of the way out to gain access to the headlamp. Step 5 - remove and replace the bulb - it is halogen so you DO NOT touch it with your fingers because the finger oil will cause a hot spot and the bulb will burn out fast. Handle the new bulb with a clean cloth - a clean sock works well.
There are three screws that holds the head lamp in place, but first you have to remove the right side radiator cover, remouve the front grill (4 screws), remouve the head lamp lower trim (one screw behind the grill and cliped at the fender), then remouve the front grill mounting bracket (2 screws) then you'll finaly reach the 3 headlamp screws (2 on top and one behind the lower headlamp trim)
the metal ring is the retainer for the bulb. you should be able to get at it from the front area without taking the grill loose. most of those only have 2 little phillips head screws. remove the screws and the bulb will come out. unplug it and the new one goes right back in. installation is the reverse of removal.