Question about 1991 Toyota Pickup

2 Answers

Toyota 1991 Pickup Truck V6 3.0 engine

I have rebuild my engine, overhaul all the Ring set, Pistons and pins, all bearings, Oil Pump, gasket set, Timing set. Am I forgot anything here? I have done once but still need input, let me know if I am missing anything;
I am going to replace cam & crank seal, water pump, thermostat, timing belt, aux belt, fuel filter. The engine had 115k mile but I hear some knocking noise so I want to open everthing up make sure all the camshaft & piston were fine in there. If your guys have any watchout or lookout list please add it on.
Thank you,
best wishes

Posted by on

  • Anonymous Feb 26, 2009

    i have knocking and backfire in the intake lol i couldent even get it started today 58 mile drive and then this how suckie its my put put car

  • Anonymous Mar 20, 2014

    the noise is hard to pin point, most likely the crank pulley bearing? I've also read about the water pump bearing?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 92 with the same motor and 121k and it knocks too. so does my friends, i think they all dew. injector cleaner stopped his but then it started again

Posted on Nov 17, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

The are many possebilities of knocking noises put but listening to what you say try check the engins cam followers

Posted on Sep 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rebuilding oil pump for a v6 Buick & how to put the piston back in


Talking about the Buick 231/3.8L - YouTube

? 7:28
https://www.youtube.com/watch?v=PBx2MgVy1V0
Dec 24, 2012 - Uploaded by WhoSaidTyler
I have been told they have a kit for that oil pump which consists of a spacer ring and larger oil pump .... Will ...

GM 3100 V6 rebuild (3.1 litre) - YouTube

? 1:49
https://www.youtube.com/watch?v=gsAMtuTbE5U
Mar 6, 2012 - Uploaded by MET-TECH LLC
New main bearings, rod bearings, camshaft bearings, piston rings, head gaskets, ... oil pan gasket, oil pump ...

GM 3.8L V6 Engine Piston Slap audio with Video - YouTube

? 3:22
https://www.youtube.com/watch?v=SGCg1KHi2NU
Oct 12, 2012 - Uploaded by seriousNoodle
It turned out to be a loose piston and unbalanced torque converter. ... Stats on Engine: 3.8L V6, GM VIN Code ...


Dec 12, 2015 | Buick Regal Cars & Trucks

1 Answer

Daewoo matiz 200 se replace complete bearings rings gaskets and the head is been overhaulled valve stem seals and compression test done start up plenty of smoke coming out of exhaust as the car getting...


have the fault codes read to determine if any sensors are out of parameters from the engine rebuild. If you did not get a rebore and you used existing pistons the smoke may be from excessive ring clearance and worn ring grooves in the pistons . I am not a believer in wearing in as all wear only gets worse (not better) but in this case may be some normal use will allow the rings to reseal in the worn ring grooves over time

Feb 14, 2014 | Cars & Trucks

1 Answer

Oil leaking from toyota camry 1992, 1994 model


You don't say what engine it has. The 4-cyl was a better than the V6 for oil leaks.

The V6 had oil leaks from

-rear bank cam cover gasket

-distributor o-ring seal

-oil filter bracket o-ring seal

-crankshaft nose oil seal (less common)

-rear main bearing oil seal (expensive, just leave it)

The 4 cyl leaked oil from

-distributor o-ring seal

-camshaft cover gasket

-rear main bearing seal (expensive, leave it)

May 21, 2012 | 1991 Toyota Camry

2 Answers

1991 Nissan 2400 pick-up, rattling sound in moter with loss of power. Oil light came on but is full of oil. what could it be?


the oil light comes on from loss of oil pressure, this can be from two things 1. your oil pump is bad abd 2. your bearings around the crankshaft are bad. If the noise is coming from the bottom of the engine, Then the bearings are bad. If the noise is at the top then this could be the distributor. the distributor drives the oil pump, there is a shaft or a pin/tongue on the bottom of the distributor. See if it is broke. Also look down the hole and see if the pump is broke. It's hard to see but you can with a good light and mirror. Just a note, If your truck has had a knock for a while(like when you start it in the morningand it goes away in a few minutes or seconds) Then the bearings are bad. It's time to rebuild or replace.

Jan 25, 2011 | 1991 Nissan Pickup

1 Answer

Chevy s-10 pick up truck ,158154, 4cyl engine, wont start


Milky substance on your dip stick indicates contamination in your engine oil, most likely coolant and that is an indication of head gasket, or intake gasket gone bad and coolant leaking into your oil system. Note that coolant in your engine oil is bad, coolant will corrode the internal engine's bearing causing you to replace or overhaul the engine. The engine not starting is most likely the result of being blown and will need to be replaced.
Thank you for using Fixya and god luck

Mar 22, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How to overhaul an engine?


TO OVERHAUL ENGINE YOU HAVE TO REPLACE ALL WORN PARTS.LIKE VALVES + SEATS+ GUIDES.+ SEALS. ALSO YOU HAVE TO REPLACE CAMSHAFT AND GEAR+ LIFTERS NEW CAM BEARINGS.NEW OIL GALLORY PLUGS AND FREEZE PLUGS.THE CYLINDER BLOCK HAS TO REBORED BEFORE INSTALLING.NEW PISTONS + RINGS+ CRANKSHAFT AND BEARING HAS TO BE REPLACED.ALSO OIL PUMP TIMING CHAIN.AND CRANKSHAFT GEAR.IT WOULD BE A WHOLE LOT CHEAPER TO BUY REBUILT ENGINE THEN TO REBUILD.BECAUSE YOU HAVE TO HAVE A LOT OF EXPENSIVE TOOLS AND HIGHLY SKILLED TO REBUILD ENGINE.ITS NOT A EASY JOB.

Oct 25, 2009 | 1995 Isuzu Rodeo

3 Answers

1991 Geo Metro very low oil preasure at idle


try heavier wt oil, check oil pump pressure, replace oil pump if needed

Sep 12, 2009 | 1991 Geo Metro

2 Answers

Oil drain out and now have no power


it is likely that when the oil drained with the motor running all moving parts within the engine started to wear rapidily this could have caused pistons or worse to seize. you will prob need a rebuild or new engine

May 20, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Oil Pump leaking on 1983 toyota pickup 20r engine.


I've had the same problem with my 22r.
I just put silicone gasket ( the stuff you get in the tube for automotive) on top of the o-ring.
It added an extra seal plus also hold the o-ring in place when putting the oil pump back on.
Never had a problem with the oil pump after that.

Apr 06, 2009 | 1983 Toyota Pickup

1 Answer

1991 Toyota Pickup Leaks oil



put new cylinder head gasket cover.clean the engine,if its check the cylinder head boltes and tight.

Sep 18, 2008 | 1991 Toyota Pickup

Not finding what you are looking for?
1991 Toyota Pickup Logo

601 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...