Question about 2003 Chrysler PT Cruiser

Open Question

O2 sensor wiring

2003mod pt.
4wires from o2 sensor
black, white, white, and grey/lightblue
question is (which is what) out of these wires??
guess black is ground, but the rest??

Posted by on

  • 1 more comment 
  • violataz Sep 10, 2008

    Cause i bought this performance-tuning ajustable chip. That needs connecting to the IAT sensor and both of the O2 sensors.. So I needed to know which of the wires is the signalwire..?..
    Both O2 sensors have 4 wires (two whites,grey and black)
    And IAT sensor has just one red and one black??? Thank you soooo much

  • shaggy3119
    shaggy3119 Nov 26, 2008

    I tested the 4 cables the 2 white 1 black 1 gray.
    Black 4.32v voltage to 3.45v
    1 white 5.8v to 5.5V
    the other white 0.3v to 0.4v
    gray 0.0v

    outo zone and ask the attendant if he knew which wire sent signal to the computer, he showed me a sensor of Bosh and show that, the black send signal to the computer ..
    and both white is the hitter,
    grey is the ground .....
    with doubts?

    I bought an air / fuel ratio gauge it goes into lean .....
    I do not know what to do?

  • Daniel Jenkins
    Daniel Jenkins May 11, 2010

    Use a voltmeter to test.

    Why do you need to know which wire is which anyways?



3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 615 Answers

SOURCE: '05 PT Cruiser O2 sensor problems.

I had a similar problem with my car. It turned out the O2 sensors were fine and the issue was a leak in the throttle body causing the engine to run lean. If you have an ODB2 scanner you can look at fuel trims, etc and will be able to tell.

Posted on Mar 28, 2010

  • 2309 Answers

SOURCE: 06 pt crusier replaced both o2 sensor and still

the fact that you replaced the sensor and the same code is there means the sensor is functioning ok, you have another problem, code readers just tell you what caused the mil light to go on, not the problem, for that you have to scan the engine on a reader and get readings from sensors and actuators, it could be a plug, vacuum leak egr malfunction, injector malfunctioon to name a few, do yourself a favor and get the engine analysed

Posted on Nov 25, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

1996. Which color wires go where?

There should have been an instruction sheet in the box with the sensor. If not, you may have to go back to the store and ask for one.
Most sensor brands are different.

Sep 16, 2015 | Mazda B2300 Cars & Trucks

1 Answer

2002 lincoln ls oxygen sensor signal wire color

White are the heaters
Black the ground

Grey (signal) or output wire

Back probe the grey wire & ground your
meter lead or oscilloscope to chassis ----- NOT THE SENSOR GROUND

No voltage goes to the O2 --- it is an output sensor

Jul 02, 2011 | Lincoln LS Cars & Trucks

1 Answer

O2 sensor wire original o2 sensor adaptor got melted by my exaust,so it was cut off the original wiring harness which had 4 wires which are red/white, orange,grey/white and grey. But the...

Ford Explorer is equipped with two oxygen sensor positioned on the exhaust manifold. Its necessary to replace the oxygen sensor at the first sign of failure. You can get all necessary details about o2 sensor at

Jun 23, 2011 | 2003 Ford Explorer

1 Answer

I need to know which wire on the 4 wire oxygen sensor (2 white, one grey one black) is the heat wire on a ford f-150 o2 sensor?

Hello! There are four O2's...Each O2 heater, left and right bank, front and rear, has it's own wire colors...These colors are "at the connector"...First series are the control ground sent by the PCM..
RR=White/Black...RF=Red/White...LR=Tan/Yellow...And LF=Yellow/Light Blue...........This series are the battery leads, hot when fuel pump relay pulls...RR=Violet/White...

If you have any questions feel free to ask...Guru...Saailer

Oct 20, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

1995 volvo o2 sensor..which wire???

the 2 whites are for the heater, the grey should be computer reference voltage. black should be the signal wire

May 23, 2009 | 2001 Toyota Sienna

1 Answer

Repacing an OEM oxygen sensor with a universal Oxygen sensor

Visit the on-line store, known as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
toyota celica

Oct 21, 2017 | 2001 Toyota Celica

1 Answer

O2 Sensor Wires

if memory is correct its the grey wire blacks ground whites are fore heaters

Jul 26, 2008 | 2000 Ford Windstar

1 Answer

O2 sensors

the white wires are the heater and the grey and black are the sensor wires the grey should be the one to the pcm

Jul 07, 2008 | 2004 Ford F250

1 Answer

O2 sensor wiring

ok the two white go to the two brown, the creame to the black and the grey to the purple,

if this don't work just swap the last two,
it will not damage any thing on your car, just if is not right it will turn the light on,
but the withe cables definly go to the brown they are only grownds

May 28, 2008 | 1996 Pontiac Grand Am

Not finding what you are looking for?
2003 Chrysler PT Cruiser Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides