Question about 2005 Ford Ranger

1 Answer

Fuel pump my truck quit and the fuel pump will not turn on. i got power and ground because my fuel guage still works but no fuel?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 89 Answers

Kinda sounds your fuel pump died on you or has trash in it need to pull it out and check but first make sure you check the fuse for it might be as simple as that your gauge is on separate circuit hope this helps

Posted on Sep 04, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda b2300 1999 pickup


bad ground to the sending unit

Aug 29, 2017 | Mazda Cars & Trucks

1 Answer

2001 chevy blazer replaced fuel pump with fuel pick up switch and fues guage still does not work


THERE SHOULD BE 3 WIRES, FROM PUMP/SENDER UNIT, 1 WIRE FOR PUMP POWER, 1 WIRE FOR GROUND, & 1 WIRE FOR FUEL GAGE, THE FUEL GAGE WIRE GOES DIRECTLY TO GAGE , INSPECT THIS WIRE , MAY CHANGE COLOR ON ITS WAY TO GAGE, WIRE MAY HAVE BEEN DAMAGED UNDER TRUCK, ALONG FRAME RAIL, OR HAS BECOME CORRODED, A BUMP IN THE WIRE INSULATION(CORROSION), ALSO, CHECK ALL GROUNDS, REPEAT, ALL GROUNDS TO FUEL PUMP CICUIT, EVEN IF THEY LOOK OK, THEY COULD BE BAD GROUNDS, YOU NEED GOOD GROUNDS TO COMPLETE ANY CIRCUIT !!! 2001 TRUCK, I'D QUESTION YOURS !!!!! WHAT SHAPE WAS YOUR WIRE HARNESS @ PUMP, THEY GO BAD, ANYTHING UNDER THE TRUCK !!!!!! STAY IN YOUCH, LIKE TO KNOW OUTCOME !

Mar 25, 2013 | 2001 Chevrolet Blazer

1 Answer

Fuel guage go up and down with little gas in tank


It does not really have a shut off relay, but it does have a relay that powers the pump. The relay is in the engine compartment.
You would need to check for power and ground at the gas tank. Sounds like the ground connection may not be good.

Feb 09, 2013 | 1992 Buick Century

1 Answer

2007 F350 4x4 regular cab V10 gas guage quit working I had the sending unit and fuel pump changed the fuel guage went to 1/4 and sat there. Any tips? Fuel guage wont work.


I'm assuming this has dual tanks, do you know if it is not working on both tanks ?
Most people would check the circuit for the gauge at the tank. The sending unit grounds the gauge on the dash.

Aug 31, 2012 | 2007 Ford F-350 Super Duty XLT

1 Answer

2001 jimmy sle. I just replaced the fuel pump. Fuel guage works. Pump does not. Checked fuel pump relay- its ok. Trucks turns over but won't start. Whats next?


Test for ground and power at your fuel pump connector. Also, the sending units sometimes come without the pump itself wired in. You have to actually splice in connections sometimes. If you get stuck, dropping the tank again and removing the sending unit to inspect could be your next step.

Jan 29, 2012 | 2001 GMC Jimmy

3 Answers

1996 Chevy k2500 5.7L gas. Turns over but no start. No guages or fuel pump initiation at key on. Quit on me the other day- shut it off then fired back up 5-10 minutes later. Drove it the next day-...


So you are saying your engine does not crank? Battery connections, at the posts and check the ground connection to the frame and/or engine. Use an OHM meter to check for breaks on wires or for bad connections (all readings should be close to zero). If that all checks out, it has to be at the starter solenoid-check there for all connections, and if they check out, I'd check for bad relays or fuses in the power distribution box under the hood, and/or replace the starter solenoid.

Jul 11, 2011 | 1996 Chevrolet C/K 2500

2 Answers

Where can I find a fuse for the gas gage on a 2004 Chrysler T&C


The gas guage does not have its own fuse but instead gets its power from the "integrated power module" that handles power delivery to the entire instrament cluster and beyond. If the guage is in-op,[doesnt work] then you will need to have a few "hands-on tests run to verify if the sending unit in the tank[fuel pump module] is functional or if this problem lyes else-where, wiring problem, bad ground,ect,ect.. One hint would be if the low fuel level l;ight still functions without the fuel guage working,then your problem is NOT in the tank and very likely is in your dash-electrical or faulty guage.
8w-40-2 106001316
8w-40-2

Jan 10, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

Fuel Pump wiring


If I understand right, I would say the normal ground for the pump is bad.
"I am guessing the pump uses a ground source to start." well, just the normal ground like for any motor, you have the power wire (gray) to the pump, then the ground wire for pump, does it branch off near the tank and find a ground? Or does it go into the tank connector and then routed back somewhere through the wiring harness? Anyway, it has to go to ground somewhere. You have the wiring right it sounds,. just make a good ground source, or find the original ground and repair it.

Mar 14, 2017 | 1999 GMC Sierra

1 Answer

93 merc topaz feul pump wiring harness question


The engine computer turns on the fuel pump for 3 seconds when you turn the key to "ON".
If the engine does not start, the pump will not run.
When you turn the key to "Start", the fuel pump runs all the time the key is held in start.
When you turn the key on, it actiavtes the power relay, which provides power to the PCM or engine computer.
The PCM then activates the fuel pump relay, sending power to the fuel pump.
You should have one wire with 12V for 3 seconds in "run" position. This comes from the fuel pump relay to the inertia switch in the trunk and then to the fuel pump.
You should have one ground wire. black
One wire going to the fuel guage.
You may have another ground iwre ging to a diode before going to ground.

Mar 30, 2009 | 1993 Mercury Topaz

Not finding what you are looking for?
2005 Ford Ranger Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...