- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
X-TYPE. Sedan and Estate (Wagon). 2.0 L, 2.5 L and 3.0 L Gasoline; ... Front Wheel Bearing and Wheel Hub (60.25.03) .... Yaw Rate Sensor (86.56.57) - 2.0L Duratorq-TDCi/2.0L NA V6 - AJV6/2.5L NA ..... Engine Oil Pressure (EOP) Sensor ...... Torque specifications are shown in the torque specifications chart located at the ...
my guess is where are the oxygen sensors?
answer 1 front and 1 rear of CAT.
where is bank 1?
well that is the bank that contains cylinder 1/
no engine options stated, or DTC errors.
Bank1 i there
Sensor 2 is rear.
A LITTLE HELP! THE O2 SENSORS ARE LOCATED ON THE EXHAUST PIPE! THERE CAN BE AS MANY AS THREE OF THEM! ON A FRONT WHEEL DRIVE, THE FIRST ONE IS LOCATED BETWEEN THE RADIATOR, AND THE ENGINE TOWARD THE BOTTOM! EACH ONE WILL HAVE A PLUG IN WIRE ON THEM! THEY ARE LONG CYLINDRICAL LOOKING TUBES STICKING IN THE EXHAUST, YOU CAN EASILY SEE THEM!
You might check this site out for Jag codes. Oxygen sensors can be a sticky job, they're screwed into exhaust and can literally weld themselves in place. Plus in most cases you need special wrench/socket to get around the sensor. (they can be a real pain)
WELL WHICH OXYGEN YOU REPLACING THE UPSTREAM OXYGEN SENSOR MOUNTED IN EXHAUST MANIFOLD AND THE DOWN STREAM OXYGEN SENSOR LOCATED IN THE EXHAUST SYSTEM AFTER THE CATALYTIC CONVERTER .YOU NEED A OXYGEN SENSOR SOCKET TO REMOVE IT.TO REMOVE OXYGEN SENSOR CRANK VECHICLE TO GET OXYGEN SENSOR HOT BECAUSE HARD TO REMOVE WHEN COLD.BECAREFUL DONT GET BURN ON EXHAUST MANIFOLD WHEN REMOVING OXYGEN SENSOR.AND WHEN INSTALLING NEW OXYGEN SENSOR USE ANTI SEIZE COMPOUND ON SENSOR THREADS.BUT MOST OF THE TIME NEW SENSOR WILL HAVE ANTI SEIZE COMPOUND ON IT.
Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2
Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2
Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.
Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.
hi from the uk the location of mass air flow sensor on x type jag is as follows==it is on the r/h/side of the air filter cover with jaguar embossed on top? this sensor is just prior to the intake hose that connects to the motorised throttle body from filter connections underneath it to unplug and meter is held by two screws ?if memory serves ? may i suggest you remove the large hose and use a little wd40 or similar to clean /lubricate the throttle butterfly in throttle body throat at this point so as to prevent future sticking upsetting of idling ? hope this helps ?