Question about 1999 Dodge Intrepid

1 Answer

Heater AC blower only runs on high. I've checked all related fuses that I know of. Is there a connection to a multi-resistor somewhere that needs to be checked? Thanks for your help.

Posted by on

  • dggivens Dec 07, 2008

    1998 dodge intrepid, I have the same problem and I have been told it is the relay, but i do not know where it is??? Can someone tell me so I can replae it ? A diagram would be very helpful



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 41 Answers

Heater module may need to be replaced

Posted on Sep 04, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Repair temp control

First. Check all the fuses-focus on the blower motor fuse. The fuse box is located near the hood release lever.
Make sure the slide levers controlling air direction and heat are at the top position. Make sure that the blower switch is on high.
Carefully pull temp control unit out about 2 inches, by removing 2 screws at bottom of unit. Get a test light, and check for current to the unit and blower motor.Make sure the connections to the switches are good.
Check the resistor connection to the blower motor. It is in the engine compartment on the AC condenser housing- at the firewall.
Check all the connections related to the blower motor and make sure there is current to the unit.
A test light will help determine what is at fault. If it is a switch behind the control unit, replace the whole unit. Your local auto salvage yard could have one.
Good luck.

Jun 19, 2014 | 1992 Chevrolet S-10

1 Answer

Why would front console blower fan only work on high?

There is a resistor somewhere that cuts the voltage down for slower speeds. High speed runs on a direct circuit.
You need to find that resistor - - may need a shop manual.

Jun 28, 2012 | 1999 Ford Expedition

2 Answers

2006 chevy silverado heater fan dont work fuse ok

replace the blowermotor resistor, it is also called a blowermotor control processor its located on heater box next to the heatercore, here a picture of it and a diagram to show you exactly were it is. this will solve your problem,hope this helps you.daf0cd2.gifc3ee9b2.jpg

Jan 30, 2010 | 2006 Chevrolet Silverado

2 Answers

Inside fan switch has 4 speeds only high works,

I have great news!It is not that bad!Look near the blower motor in the blower case housing ther is a blower resistor.It will have a multi-wire plug in.Unplug this ,and remove the two screws that retain the resistor in the box.Pull the resistor out ward,it will be out.The part store will have it or can get it for you.This is your speeds for your blower motor.If the blower is making any kind of racket,or seems to be slow when it is on high selection,replace it also,cause this is the cause if the resistor going out.

Aug 21, 2009 | Dodge Dakota Cars & Trucks

1 Answer

Heat/ac blower motor works on high. intermittent on other speeds.

Check the blower resistor pack - usually located in the heater air ducting in the blower fan airflow. Check for loose connections and open circuit resistors on the unit.
If speed 4 works always, its unlikely to be the blower motor ground connection.

Aug 10, 2009 | 2004 GMC Canyon

3 Answers

Subject: 2004 isuzu ac/heater blower is not working

The resistors are in circuit only on the lower fan speed settings.
On the highest speed setting, power is switched directly to the fan motor.
Check fan power supply fuses,
Check power is available to the fan when high speed selected.
If all above OK, apply power directly to the motor to verify fan motor runs- if it doesn't the motor may need replacement/repair.

Jul 29, 2009 | 2004 Isuzu Rodeo

3 Answers

Blower speeds on ac/heater for 2003 chevy pickup(v6)

Hi, sounds like your blower motor resistor needs to be replaced. If not the resistor, check the blower motor.

Jul 27, 2009 | 2008 Dodge Ram Pickup 1500

2 Answers

VW Jetta GL 2000, AC - Heater Fan stopped

blower motor or resistor or the blower motor control switch.

Jun 01, 2009 | 1998 Volkswagen Jetta

2 Answers

Air blower will not run on high

It's heater controls r in limp mode,need to replace temp. resistor,located in heating ducts somewhere not familer with that exact model

Mar 10, 2009 | 1997 Buick LeSabre

1 Answer

Heater Control Switch Only Works on High

It appears there is a resistor block there, either at blower connection area, or at firewall area on passenger side under cowl somewhere. It is quite common for blower to only work on high when resistor goes. Look for block, or base, 1-1/2" x 3" approx. with electrical connector to it.

Feb 10, 2009 | 2002 Chrysler Sebring

Not finding what you are looking for?
1999 Dodge Intrepid Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides