Question about 2000 Hyundai Sonata

1 Answer

Error code er 2

I actually have a 2001 Hyundai XG 300 L that is reading an error code er 2 on the radio. I can't figure out what is causing the problem. I have tried cleaning the cd player and spraying the inside with canned air to maybe get rid of any dirt or debri, but it stills has issues. It will switch back and forth from radio to cd like there is a cd in the player, but then the error code comes up. Can you help?

Posted by on

  • 1 more comment 
  • Doug Grenoble Nov 10, 2008

    My 2001 XG2001 does the same thing, constantly switching back and forth from FM radio to the CD player. Anyone else? Cause? Fix? Doug

  • ralpert Nov 28, 2008

    I get the same error #2 and when I insert a CD there is a clicking sound.

  • Anonymous Jan 30, 2009

    I have the same problem too! Very frustrating!! HELP us fix it!!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

I dont want to guess a solution for this however, ERR2 represents EJECT. The description of this error is "The Eject is not available". Possibilities are, jammed mechanism or sticky eject button.

Posted on Sep 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai XG 300 2001. reading a P1632 Engine code. Controller Area Network Bus, OFF. I know how (C.A.N) works I dont know how to fix it. HELP.


P1632 indicates a malfunction in the traction control system.
Probable causes:
1. Faulty sensor
2. Damaged/corroded connector terminal contact
3. Wire harness fault. Check for correct voltage, open, short to ground, short to voltage
4. Control unit software needs updating
5. Faulty PCM or ECM

Dec 07, 2016 | 2001 Hyundai XG300

1 Answer

On m a 2004 hyundai xg 350 i in have a check engine light that TN won't clear. I've hooked a diagnosed reader it shows code PO136 O2 sensor circuit bank 1 sensor 2. I I have replaced that sensor & i...


After fixing you sometimes need to delete the fault codes that er registrered on your ECU "electronic control unit, or car computer". You do that by using the ODB device and on that device select to delete fault codes.

Feb 13, 2015 | Hyundai Cars & Trucks

1 Answer

Finding the mass air flow sensor on a 2001 hyundai xg-300


in the intake air hose between the engine air filter & the throttle body

Sep 09, 2011 | 2001 Hyundai XG300

1 Answer

My hyundai granduer xg 300 2001 model turns over but doesent start but there is no spark in spark plugs what could cause this problem?


if it is only no spark, check crank sensor and coil. the crank sensor tells the coil when to spark

Dec 16, 2010 | 2001 Hyundai XG300

1 Answer

Where is the vehicle speed sensor located on my hyundai 2001 xg 300


It should be located beside the brake caliper either on front or rear wheels (not sure about side but surely on both wheels) will look like a small tube pointing towards the hub.

Sep 30, 2010 | 2001 Hyundai XG300

1 Answer

Trying to remove and replace the right rear wheel bearing on a Hyundai xg 300 2001 model


you have to remove the caliper first than your disk brake(this is a hub assembly) on the back of the weel bearing you should have 3 big bolts remove them put a chain on 2 of the stud of the weel put back the nut on them (if you don't have the tool to do it)than take a steel bar and do like a (slege hammer) just few hit it should come out!..hope this will help you. lipak!...

Mar 29, 2010 | 2001 Hyundai XG300

Not finding what you are looking for?
2000 Hyundai Sonata Logo

1,704 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

66302 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...