Question about 1995 Ford Windstar

1 Answer

Wiper motor My wiper motor went out. Bought a new one, have the three screws out, can't figure out how to remove the arms so I can take the old one out?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Pull the center nut out an work the arms off a little at a time. they sell a tool 2 remove the arms.it is cheep.

Posted on Oct 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the wiper motor on a 1994 volkswagon golf


The wiper motor on a Volkswagen is an electric motor connected through a drive linkage to the wiper arms. Windshield wipers are an integral feature for operating a motor vehicle safely. If your wipers are not functioning, or seem to lack the speed or power they used to have, the wiper motor should be removed and replaced immediately
.


Location
  • The wiper motor on a Volkswagen is located directly underneath the plastic cowl cover. The cowl cover is located directly below the windshield.

Removal
  • Begin by removing the wiper arms by prying off the covers at the base of the arms and removing the nuts that secure the arms to the drive shafts. Label the passenger and driver arms so they can be installed in the same positions. They are not interchangeable. Remove the rubber hood to cowl weather seal. Unscrew the plastic fasteners from the driver's side of the cowl cover, then remove this half of the cover. Remove the fasteners from the passenger's side cowl cover and remove this half of the cover. Disconnect the windshield wiper motor wiring harness by separating the plastic wiring connector. Remove the three bolts that secure the wiper motor to the vehicle's body. Pull the motor slightly away from the body, then remove the nut that connects the motor shaft to wiper linkage. Remove the motor.

Installation
  • Place the new wiper motor into position in the cowl and reconnect it to the wiper arm linkage. Then reinstall the three retaining bolts. Reconnect the plastic wiring connector to the wiper motor wiring harness. Place the cowl covers into position below the windshield and reinstall the plastic fasteners that retain them. Reinstall the rubber hood to the cowl weather seal. Reinstall the wiper arms in the same position you removed them from, along with the wiper arm retaining nuts and lower wiper arm covers. Turn the windshield wipers on and test for proper operation. If the wiper blades slap against the bodywork surrounding the windshield, loosen the nuts that connect the wiper arms to the shafts and adjust.

More Read: OBD2 car diagnostic tool

Aug 06, 2012 | 1994 Volkswagen Golf

1 Answer

Engine schematics 2002 pontiac montana


Hi there:
Isnt a diagram but If you have removed the motor, here is the motor installation procedure....

INSTALLATION PROCEDURE

6_23_2012_11_48_33_pm.gif

Align the wiper motor to the wiper drive system module. NOTE: Refer to Fastener Notice in Service Precautions.
Install the wiper drive system module to wiper motor screws. Tighten Tighten the wiper drive system module to wiper motor screws to 7 N.m (62 lb in) .
Connect the electrical connector to the wiper motor.
Install the crank arm on the wiper motor.


6_23_2012_11_49_39_pm.gif

Rotate the washer solvent container into the installation position.
Install the washer solvent container screws. Tighten Tighten the washer solvent container screws to 6 N.m (53 lb in) .
Inspect the wipers for proper operation.


6_23_2012_11_51_04_pm.gif

Also, here is the crank arm procedure...

REMOVAL PROCEDURE

Remove the wiper system module cover.
Remove the drive link from the wiper motor crank arm.

2.1. Loosen the drive link screws.
2.2. Remove the drive link from the wiper motor crank arm.

Remove the wiper motor crank arm cover and seal.
Remove the wiper motor crank arm from the wiper motor.

4.1. Loosen the wiper motor crank arm screw.
4.2. Tap on the wiper motor crank arm screw with a soft-faced mallet while holding up on the wiper motor crank arm until the wiper motor crank arm loosens from the wiper motor.
4.3. Remove the wiper motor crank arm screw and the wiper motor crank arm from the wiper motor.

INSTALLATION PROCEDURE


6_23_2012_11_52_10_pm.gif

Install the wiper motor crank arm onto the wiper motor.

1.1. Turn the ignition switch to the ACCY position.
1.2. Set the wiper switch to PULSE position. The wiper motor should be operating.
1.3. Turn the ignition switch to OFF when the wiper motor is in the innerwipe position.

IMPORTANT: Do not rotate the wiper motor shaft during the installation of the wiper motor crank arm.

1.4. Install the wiper motor crank arm on the wiper motor while maintaining a 4-8 mm (0.157-0.315 in) gap between the V-grove in the wiper motor crank arm and the tab.

NOTE: Refer to Fastener Notice in Service Precautions.

Install the wiper motor crank arm screw. Tighten Tighten the wiper motor crank arm screw to 16 N.m (12 lb ft) .
Install the wiper motor crank arm cover and seal.


6_23_2012_11_52_52_pm.gif

Check the gap between the wiper motor crank arm and tab. If the gap is not 4-8 mm (0.157-0.315 in) , remove the wiper motor crank arm and repeat installation steps.
Install the drive link onto the wiper motor crank arm.
Install the drive link screws. Tighten Tighten the drive link screws to 5 N.m (44 lb in) .
Install the wiper system module cover.
Inspect the wipers for proper operation.

Additional procedures: Wiper Motor Module Replacement.

TOOLS REQUIRED
J 39822 Wiper Arm Puller

REMOVAL PROCEDURE

Turn the ignition switch to the ACCY position.
Set wiper switch to the PULSE position.
Turn the ignition off when the wiper arms are in the innerwipe position and not moving.
Disconnect the washer hose from the washer nozzle.
Remove the cover from the wiper arm nut.
Remove the wiper arm nut from the wiper transmission drive shaft.
Using J 39822 remove the wiper arm from the wiper transmission.
Remove the wiper blade from the wiper arm.
Clean the knurls of the wiper transmission drive shaft with a wire brush.



Install the wiper blade onto the wiper arm.
Install the wiper arm onto the wiper transmission drive shaft. IMPORTANT: Hold the measuring device at 90 degrees (perpendicular) to the wiper blade tip.
Measure the distance from the wiper blade tip to the solid edge of the windshield blackout. Position the wiper arms at the following distances:

LH - 147 mm (5.79 in) above the glass blackout.
RH - 123 mm (4.84 in) below the glass blackout.

NOTE: Refer to Fastener Notice in Service Precautions.



Install the wiper arm nut onto the wiper transmission drive shaft. Tighten Tighten the wiper arm nut to 48 N.m (35 lb ft) .
Install the cover on the wiper arm nut. IMPORTANT: Lubricate the washer hose with the windshield washer solvent to ease installation on the washer nozzle.
Install the washer hose on the washer nozzle.
Inspect the wipers for proper operation.



Remove the wiper arms from the vehicle.
Remove the air inlet grille panel.
Remove the wiper motor.
Remove the air inlet panel to wiper motor module screws.
Remove the wiper motor module from the vehicle.
Remove the insulators from the wiper motor module.

INSTALLATION PROCEDURE

Install the insulators onto the wiper motor module.
Align the wiper motor module to the air inlet panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the air inlet panel to wiper motor module screws. Tighten Tighten the air inlet panel to wiper motor module screws to 10 N.m (89 lb in) .
Install the wiper motor.
Install the air inlet grille panel.
Install the wiper arms onto the vehicle.
Inspect the wipers for proper operation.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 2002 Pontiac Montana

1 Answer

Can you please give me instructions on replacing the wiper motor pulse board module on my 95 Chevy Van G20?


This is a very simple procedure and will save you lots of money by replacing it yourself! A common replacement item on GM vehicles, it should be readily available at your local auto parts retailer and should take no more than a half-hour with just a couple of tools.


• Turn the ignition key to the OFF position.
• Remove the Connector Position Assurance (CPA) and disconnect the wiper motor electrical connector.
atye.gif
• Remove the three screws that secure the cover to the wiper motor and remove the cover.
• Inspect for sealant on the inside of the cover and then discard the cover and screws. Important: If sealant was found on the old cover, it will be necessary to remove any old sealant from the motor housing in Step 6.
• Carefully remove the module (circuit board) from the wiper motor by lifting up on the end of the module electrical connector.
• If necessary, remove any old sealant from the wiper motor housing (refer to Step 4). Notice: When handling the new module in the next step, be careful not to damage or band the electrical contacts on the bottom side of the module.
• Install the module into the wiper motor housing, making sure that the module is fully seated. When fully seated, the edges of the module circuit board will be flush (even) with the motor housing along all sides.
atye_0.gif
• Carefully apply a bead of silicone sealant, P/N 12345739 (or GE-162 sealant or equivalent) in the groove of the NEW cover (Figure 2). Remove any excess sealant that is outside of the groove. Important: Only apply enough sealant to fill the groove in the cover.
Install the new cover on the wiper motor housing and install the three new screws.
• Tighten the screws to 2.6 N·m (23 lb in).
• Reconnect the wiper motor electrical connector to the wiper motor assembly and install the CPA.
• Turn the ignition key to the ON position and check the wiper system for proper operation (delay/low/high/etc.).



May 04, 2011 | Chevrolet G20 Cars & Trucks

1 Answer

Windshield wiper moter went out i need to change it out. how do i change it?


  1. Disconnect the negative battery cable.
  2. Remove both wiper arm and blade assemblies.
  3. Remove the cowl grille attaching screws and lift the cowl grille slightly.
  4. Disconnect the washer nozzle hose and remove the cowl grille assembly.
  5. Remove the wiper linkage clip from the motor output arm.
  6. Disconnect the wiper motor's wiring connector.
  7. Remove the wiper motor's three attaching screws and remove the motor. To install:
  8. Install the motor and attach the three attaching screws. Tighten to 60-85 inch lbs.
  9. Connect wiper motor's wiring connector.
  10. Install wiper linkage clip to the motor's output arm.
  11. Connect the washer nozzle hose and install the cowl assembly and attaching screws.
  12. Install both wiper arm assemblies.
  13. Connect the negative battery cable.

tecnovative_158.gif

Installing the wiper arm connecting clip.


tecnovative_159.gif

Feb 25, 2011 | 1992 Ford F250

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

I'm looking for instructions on how to replace the window wiper motor and switch


Windshield Wiper Motor Removal & Installation To Remove:
Using the J 39232, remove the wiper transmission from the wiper motor crank arm. gmpc_wa_1.gif

  1. Remove the wiper arms
  2. Remove the air inlet grille panel.
  3. Disconnect the connectors from the wiper motor assembly.
  4. Remove the three screws and the wiper drive system module.
  5. Using GM special tool J 39232 or equivalent, separate the wiper motor crank arm from the wiper drive ball joint.
  6. Remove the wiper motor crank arm from the wiper motor.
    • Remove the rubber boot.
    • Loosen the mounting screw.
    • Tap on the screw with a plastic or leather faced hammer while supporting the wiper motor crank arm.
    • Tap the screw until the crank arm is loose.
    • Remove the screw and crank arm from the motor.
  7. Remove the three screws and separate the wiper motor from the module assembly.
To Install:
  1. Position the wiper motor on the wiper drive system module assembly. Install the three mounting screws. Tighten the screws to 62 in lb (7 Nm).
  2. Install the wiper motor crank arm on the wiper motor.
    • Connect the wiper motor electrical connector.
    • Turn the wiper switch to the accessory position.
    • Turn the wiper switch to the pulse position.
    • Turn the wiper switch off when the wiper motor is in the middle of the wipe cycle.
    • Disconnect the connector from the motor.
    • Maintain a gap of 0.157-0.314 in (4-8 mm) between the wiper motor crank arm and the bracket tab. If the gap is not 0.157-0.314 in (4-8 mm), remove the wiper motor crank arm and repeat installation.
    • Install the mounting screw. Tighten to 142 in lb (16 Nm).
    • Install the rubber boot.
  3. Position the wiper drive system module on the vehicle. Install the three mounting screws. Tighten the screws to 68 in lb (10 Nm).
  4. Using GM special tool J 39232 or equivalent, connect the wiper motor crank arm to the wiper drive ball joint.
  5. Connect the wiper motor assembly electrical connector.
  6. Install the air inlet grille panel.
  7. Install the wiper arms.
  8. Check the windshield wiper operation.
---

Oct 28, 2010 | 1999 Buick Regal

1 Answer

Need to remove my wiper assembly on my 1995 plymouth voyager to remove my wiper motor


the cowl grill by the front of the windshield must be removed [6 screws, three in the grill and three along the front edge] to have access to the crank arm. Remove the nut from the crank arm to detach from the wiper motor

Sep 21, 2010 | 1995 Plymouth Voyager

1 Answer

Front winsheild wiper motor


unplug old motor
remove plastic at base of windshield
remove the nut that attaches the wiper arms to the motor
remove the three bolts that attach the motor to the firewall
install the new one by reversing these steps
Hope this helps!

Mar 05, 2009 | 1998 Chevrolet Suburban

1 Answer

Front wiper motor not working


disconnect the negative battery post.
disconnect the harness from the wipper motor, using a 8mm socket, loosen the two crank arm socket screws and lock-washers until the socket releasesfrom the crank arm ball. do not remove the crank arm from the motor.
using a 10mm socket, remove the three motor retaining screws, slide the motor out of the slot in the bracket.
To install make sure the wipers are in the park position, slide the motor into the slot in the bracket. using the 10mm socket, install the three motor retaining screws and tighten to 49-80inch lbs.Using the 8mm socket tighten the two crank arm socket srews and lock washers. connect the harness to the wiper motor.connect the negative battery cable

Jan 23, 2009 | 2003 Chevrolet Venture Passanger

1 Answer

Wiper arm removal 1997 GMC Jimmy


youll have to raise the hood on the truck to access the screws that hold it in place there should be 2 of them holding it

Oct 25, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...