Question about 2002 Pontiac Grand Am

2 Answers

Blinkers work sometimes, sometimes they don't

Sometimes they work and when they don't nothing happens. Sometimes if they don't work if I put my hazard lights on and then turn the hazard lights off then the blinker starts to work.

Posted by on

  • booyah3940 Sep 03, 2008

    How do you fix that?

  • booyah3940 Sep 03, 2008

    How do you fix the hazard switch?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Here is some extra information on replacing the Daewoo Lanos indicator / hazard lights relay. Open the driver door, on the side of the dashboard there is an access panel. Flip it open with a screwdriver.
Now you can pull out a violet connector block. The relay is plugged into this block, it is green. You can just pull it out of the connector block and replace it by a new one. The part number is 96312545, and it has three pins, numbered 31, 49 and 49A.
Other specifications: 12V 2/4x21W. It is made by Daewoo / DECO. The same type of relay is used in the Daewoo Matiz. I picked up a used relay from an old Matiz for 2 euros and the indicator/hazard lights work like
a charm again. The whole replacement took about 2 minutes, but it took me days to get the used part. Probably other relays with these three pins will work too: google for "31 49 49A". Hope this is useful to other people who run into problems with the Daewoo Lanos indicator lights!

Posted on Jun 15, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

Sounds like the flasher(which is your hazard switch) is failing.

Posted on Sep 03, 2008

2 Suggested Answers

  • 2841 Answers

SOURCE: blinker and hazard light problems

Replace the flasher relay. Sorry I cannot tell you where it is. Buy a new one so you will know what you are looking for.

Posted on Mar 03, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both blinkers don't work but flashers do


There should be a flasher unit on the fuse box under the dash for the turn signals and another behind the dimmer switch for the hazards.
Sometimes one of the flashers is behind the fuse box in the glove compartment if equipped.
Don't be surprised if the flasher is not the problem. Most of the time the problem is the multi-function switch on the column.
There are stories online about using WD40 to take care of the switch problem.

Sep 12, 2012 | 1996 Ford Taurus

1 Answer

Sometimes my blinkers don't work in my 2000 impala


I had the same problem with my 2000 Impala. It stumped me for 2 1/2 yrs. I just replaced the hazard warning switch, it solved the issue. I hope this helps.

Jun 01, 2012 | 2000 Chevrolet Impala

1 Answer

Intermittently my blinkers stop working. When this happens my hazard lights do not work, neither does the traction control button, wiper sprayer, high beams, nor does the bottom driving lights. I've...


The turn signal socket, where the bulbs are fitted, needs to be inspected.Also the wiring needs to be inspected.Wiggle the socket and wiring a bit, then check, if the blinkers start working or not.---------- There is a troubleshooting procedure to confirm the fault,Click this link below and go through the procedure :--- http://howtobyme.blogspot.com/2011/09/blinkers-works-intermittently-on.html ---------- This will help.Thanks.Helpmech.

Sep 19, 2011 | 2007 Chevrolet Tahoe

1 Answer

Blinkers only work sometimes


chevy had an issue with the blinkers and hazards not working all the time i found that when my turn signals stop working push the hazard switch until they blink then the turn signals start working again. its a faulty turn signal/hazard switch that needs to be replace costs about 30 bucks pretty simple to replace.

Dec 24, 2010 | 2000 Chevrolet Malibu

2 Answers

Turn signal doesn't come on until I hit my hazard light on & off


it could be duel filament bulb that is blown and shorting inside the bulb to the other circuit, you may need to remove all indicator and hazard bulbs and check. I would also try a new flasher can

Apr 17, 2010 | 2003 Chevrolet Impala

2 Answers

Blinker and hazard light problems


Replace the flasher relay. Sorry I cannot tell you where it is. Buy a new one so you will know what you are looking for.

Mar 02, 2010 | 2004 Saturn VUE

2 Answers

Blinkers randomly do not work. Sometimes they will work and sometimes when I put the blinkers on by pushing the lever nothing happens. The lever stays on as if the blinkers would be on but no lights are...


no. its the 4 way flasher thats bad. if you pop off your center air duct covers you can get to the flasher box. you have to unplug the cruise and 4 way flasher take out the box and get a new one. they are about 80 bucks. i have just been slapping the top of the dash and they tend to work after one or two hits.

Oct 07, 2009 | 1999 Oldsmobile Intrigue

3 Answers

Blinkers and hazards not working on Jeep GC


HI. the flasher is faulty or damaged. replacing this device will fix your issue.

May 27, 2009 | 2002 Jeep Grand Cherokee

2 Answers

Hazards and blinkers not working


There are separate fuses for the turn signals and blinkers, but you should check both of them just to see if they're good.

You may have a burnt out turn signal bulb as well. I know that this sounds like an obvious answer, but a single bulb can sometimes disable the entire system because of the way that some flashers operate.

You could also have a defective turn signal/hazard light flasher. This is located under the dash board on the driver's side between the steering column and the door. You have to remove the sound insulation/kick panel (the cover on the bottom of the dash board) to reach the flasher (it is easy to remove - I don't think you even need tools).

May 16, 2009 | 1997 Pontiac Grand Am

3 Answers

Turn Signals/blinkers


Did you double-check to be sure the fuses are intact and not blown? If they are OK, it could be a turn signal relay or the switch itself (I have firsthand experience with the switch failing with respect to headlight operation, so there's no reason to believe that it couldn't fail for turn signal operation as well).

If you find that it's the switch, reply here and I can walk you through its replacement - it's about a five minute job.

Aug 10, 2008 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...