Question about 1991 Eagle Talon

2 Answers

Blower motor Where is the fuse located for the blower motor(fan)? Turn on fan and only hear a click. Not sure if there is a fuse involved or the motor is shot.

Posted by on

  • Anonymous Mar 15, 2014

    the fan want turn on

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

The fuse should be located in the fuse panel under the dash on the drivers side. the relay will be located in the junction box under the hood. if you have a owners manual it will show which fuse is what and amprage. if these are good it could be a bad switch, however if you turned it on and heard a click i would say that your relay is bad. please rate this

Posted on Sep 03, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Eagle Master
  • 61,129 Answers

You have power the fact that you hear the blower relay click tells me that. In this case I think the reason the Blower Motor Relay is clicking is because you have a bad Blower Motor Resistor. . So that would be the first thing to check out.

Posted on Sep 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi,my 07' Barina,the fan in the dash has stopped working I put it on 1,2,3or4 and nothing.on 4 I hear a click coming from drivers side fuse box fuses are fine,is the fan blower motor burned out?


not normally

the fan motor has a resistor
that part give you the different speeds
they fail and can be replaced

location not far from the blower motor




c8d5dda3-4062-4b78-a486-73db650ade6c.jpg

26329195-li4g2rdronquokdv0yx25uce-5-2.jpg

Oct 27, 2016 | Holden Barina Cars & Trucks

1 Answer

Heater fan works for a while then cuts off till it cools down




What can go wrong with a blower motor?
There are several things that may cause your blower motor to stop working. The simplest cause would be a blown fuse. If you replace the fuse and it quickly blows again, then you probably have an electrical short. Disconnected wires on the exterior of the blower motor can also cause it stop working, and if your blower motor gets dirty, it can get clogged or muddy which keeps the fan blades from spinning.

How do I test my blower motor?
When you are troubleshooting your blower motor, it is best to start by running the air conditioning or the heater to see if you can hear the sound of the fan. If you can hear the fan, it could be clogged or corroded with dirt. If you do not hear the fan, then you may have a bad resistor, blown fuse, or a loose wire. Next, you should replace any blown fuses in your car's fuse panel and try to start the blower motor again. If another fuse blows right away, you have an electrical short. If it doesn't blow out and the motor is still silent, then something else is wrong. In the case where the fuse lasts for a little while as the fan spins but then the fuse blows again, that usually means you need to replace the brushes on the motor. Finally, you can pull the motor out and visually inspect it for loose wires. If you don't see any and still want to test, try hooking it up to the battery to see if the motor will start. If all these tests still find you with a dead blower motor, it's definitely time to replace it.

How do I replace it?
Usually located under your vehicle's instrument panel, the blower motor can be removed and replaced. You'll need to disconnect the blower motor connector and remove the retaining screws holding it into place. Detach the fan retainer clip from the motor shaft that's located in the center of the blower wheel. You may need to save that piece if you are not replacing the whole motor. Inspect your new motor to ensure nothing is broken and the blades can properly spin. Re-attach the fan retainer clip, the retaining screws, and the connector so you can test your new blower motor out.

Dec 13, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

Blower motor doesn't work, how do I find out if its the fuse, relay or if the motor itself is shot? I know where the fuse box is but some of it is abbreviated and I don't know what some of it stands for....


The blower motor can be tested by removing the lead to it and seeing if it has 12 Volts by observing if the 'test light' lights up when the dash controls indicate that the blower motor should be operational.

One can test the fuses by using a 'fuse tester' available from Walmart or an auto parts store which will light up when an energized circuit has a blown fuse.

The blower motor is located on the firewall on the passenger side, in general on GM cars from the 1990s.

You may have to remove some items to get to it, though.
Blower Motor REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. If necessary, tag and disconnect the number 2, 4 and 6 spark plug wires from the ignition coil and move the coil out of the way.
  3. For 1993-99 vehicles, remove the nuts and cross brace bar.
  4. Detach the electrical connections from the blower motor.
  5. Disconnect the cooling tube from the blower motor.
  6. Unfasten the screws securing the blower motor to the blower module assembly.
  7. Remove the blower motor and fan assembly from the module.
  8. If necessary, unfasten the nut attaching the fan to the blower motor shaft, then pull the fan from the blower motor. Fig. 1: The blower motor and fan assembly is mounted in the heater and A/C module, and is accessible from the engine compartment 89636g22.gif
    Fig. 2: You can disassemble the fan from the motor by removing the retaining nut 89636g23.gif
    To install:
  9. If the fan was removed from the motor, position the fan on the shaft, then install the retaining nut. Tighten the nut to 12 inch lbs. (1.4 Nm).
  10. Position the blower motor and fan assembly to the module, then install the retaining screws. Tighten to 5 inch lbs. (0.6 Nm).
  11. Connect the cooling tube to the blower motor.
  12. Attach the electrical connector to the blower motor.
  13. On 1993-98 vehicles, install the cross brace bar and retaining nuts. Tighten the nuts to 18 ft. lbs. (25 Nm).
  14. If removed, install the coil and connect the spark plug wires, as tagged during removal.
  15. Connect the negative battery cable.
prev.gif next.gif

Nov 19, 2010 | 1997 Oldsmobile Eighty Eight

10 Answers

1997 Isuzu Rodeo V6 4X4. I have only owned this vehicle for 3wks and the fan/ac wont blow at all out the vents. The blue light comes on when i push the ac button but that is all it does. I don't know which...


C-19 Blower motor fuse 25A located in cabin fuse box. Left hand footwell on LHD vehicles, right hand dashboard on RHD vehicles.
Start by checking blower relay B-36 in the engine compartment fuse and relay box. Remove the relay. Jumper directly from battery to pins 85 and 86. (also see here: http://www.fixya.com/cars/r5544622-wire_relay if you dont know about relays) The relay should click Now measure across pins 30 and 87. Measurement should be 0 ohm.
Remove the blower motor(3 screws on the bottom of the unit under the passenger side dash) and connect jumper leads from the battery directly to the blower motor to see that it operates.
The blower motor resister is mounted on the ducting between the motor housing and the heating unit. Remove to test
Measure :
  • pin 1-2 : 2.4 ohm
  • pin 2-4 : 0.9 ohm
  • pin 2-6 : 0.28 ohm
  • pin 2-3 : 0 ohm

Aug 21, 2010 | 1997 Isuzu Rodeo

1 Answer

My heater fan stopped working how do i fix it.


either the fuse to your heater blower motor is blown or the blower motor itself is shot. Check owners manual for location of blower motor fuse and make sure it is good, if that still doesn't work you may need to take it is to have it tested to see if the motor is bad. If you know how to test with a multimeter you can do that as well and just replace it yourself if it is bad. It is often tricky to change because it is on the firewall in the engine bay generally.

Nov 19, 2009 | 2001 Volkswagen Jetta TDI

2 Answers

My heatting systom doesn't work


Chances are it's the blower motor resistor.  When that goes bad, the blower won't work, except on maybe high speed.  It's generally located right near the blower motor, which is probably under the dash board on the passenger side.

Aug 26, 2009 | 1995 Oldsmobile Achieva

1 Answer

No fan


sounds like the relay is turning on sending the power out to the blower motor resistor witch is locate dby the blower motor it is held in the case by two screws check it for power when you turn the switch on and off

Jan 11, 2009 | 1990 GMC Sierra

1 Answer

Does not blow when heater is on? blower motor


First check fuse panel for burned fuse, if all o.k., Take a look up under passenger side dash, it's usually a common spot.When you find it, locate wires going into it & probe with 12vdc test light for power with key on & fan in run position. If light comes on by probing one of the wires, your fan motor is shot, if nothing at either wire, start back tracking for relay & switch malfunction.

Dec 10, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
1991 Eagle Talon Logo

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

61117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...