Question about Toyota Corolla

2 Answers

How do I remove the driver's door panel on my Toyota Corrolla 3 door automatic please? I then need to repair the electric window mechanism somehow. Many thanks. Cyril.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Ffirst remove all screws that are holding it on approx 10, most are hidden by small round circles of plastic the same colour as the panel next you to be firm and pop it off from the door carefully there is about 10 of these clips which "pop" off then carefully lift upwards slighty unplug your electric window switch by pushing the tab on the plug itll come off. that's your door panel off. be carefull not to bump and of the metal wires you see running inside the door as these are to do with you door lock. to fix window gently pull down plastic moisture sheet on door first try another switch or give your switch a good clean, you can disasssemble it with a small screwdriver carefully, if still no difference replace your electric window motor which is bolted to the door in 3 places with 10mm bolts and is bolted to the window, unsure of what it is follow the wiring from the electric switch you unplugged will lead you to the electric motor, have fun

Posted on Sep 03, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I want to put speakrs on the the two front doors of a toyota corola 2003 how do i take them off

Posted on Sep 22, 2009

  • dcarranza17 Sep 22, 2009

    i have manual windows on my car its a 2003 toyota corola how do i take off the door panels so that i can replace the speakers. i toke the screws and everything else off but i dont know if i should pull the panel hard



    what do i do?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump on a 1988 toyota corrolla station wagon


I don't know if your fuel injected or carb? If your fuel injected, probably electric fuel pump, in the gas tank. If not fuel injected, probably a mechanical fuel pump, under the hood, note picture.

fuel-pump-1988-toyota-corrolla-station-px1oa4s1mnc4r5fmbg0hxgth-5-0.jpg

Mar 06, 2016 | 1988 Toyota Corolla 4 Door

1 Answer

Window stuck on driver side on 1996 Toyota t 100


mechanism broken inside / if electric then possibly motor faulty.
remove the door panel trim and check

Dec 23, 2015 | 1996 Toyota T100

1 Answer

WHEN I ROLL UP THE DRIVER FRONT WINDOW IT GOES UP THEN ROLLS HALF WAY DOWN BY ITSELF


Hi there,

If manual window winder

Your driver's window glass may have come off the regulator mechanism.


If electric window control

The glass may have detached from the regulator or the regulator cable has unwound itself off the mechanism (ie tension during upward motion, but loose when motor stops winding).

Your driver's door panel will need to be removed to inspect your window regulator operation.

Jun 07, 2011 | 2006 Toyota Sequoia

2 Answers

Drivers side window came off track and now free falls,how complicated is the fix,ie removing door panel..


on a scale of 1 to 10 (1 being anyone over the age of 15 , 10 being specialty training / tools) I would rate this a 3 .

The glass didnt just fall off the track... they are designed not to do that. Something must have seperated or broke off in the door somehow ( from slamming the door when entering / exiting).

Take the arm rest off and then the interior door trim pannel. be careful pealing the plastic barrier back to gain access ( and always repair any damage done to this plastic barrier to re seal the door).

If you need a video , look it up on youtube, there are a few.

Feb 19, 2011 | 1993 Chevrolet Caprice

1 Answer

How to remove inner door panel 2000 toyota corrolla


Remove the the arm rest pad. It should pop off, check if there is a phillips screw. The power window bezel will pop out as well. Lifer up and remove connector. The inner door handle, remove the screw. Then the door trim pulls off, there is about 7 plastic clips that hold the perimeter of the trim. If you have a flat head screw driver it can help. Pop off all clips and lift in an upwards direction.

Jun 09, 2010 | 2000 Toyota Corolla

2 Answers

Where is the fuse panel on a 1991 toyota corrolla


Inside compartment, in front of driver door. Under hood, behind battery.

Feb 20, 2010 | 1991 Toyota Corolla

1 Answer

2003 ford taurus drivers window will not go up.


you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the front door trim panel screws.
  1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the front door trim panel.
    • Disconnect the electrical connectors.
c64985a.gif --------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) s2h~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation
  1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.
  1. Disconnect the front door window regulator motor electrical connector.
  1. Remove the window regulator rivets.
-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation
  1. Close the window.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the radio speaker.
  1. Position the watershield aside.
  1. Disconnect the door window regulator motor electrical connector.
  1. Remove the bolts and the door window regulator motor.
---------------------------------------------------

May 04, 2009 | Ford V6 Pony Cars & Trucks

1 Answer

1991 Nissan Maxima: Removal of front driver side door panel


This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal

Mar 20, 2009 | 1990 Nissan Maxima

1 Answer

Drivers side widow will not go down more than 2 inches


A) Remove the screws in the following locations:
  1. Door handle
  2. door grip
  3. Middle of panel, 3/4 down the panel from the top
B) Removal of door Handle

  1. Use caution
  2. Slide the door handle in the direction of the motor
  3. The door handle is now freed from the door
C) Partial removal of door panel
  1. Insert a dull instrument into the port that is located on the panel roughly half way down the panel and the side the furthest from engine.
  2. Carefully pry the panel loose.
  3. With your hands, remove the panel by its contour. There are roughly 10 or so plastic plug
D) Tricky Part; Removal of door Handle

  1. Free the door handle from the panel, by carefully pushing it through the panel on an angle...
  2. You can now push the panel up beyond the door lock button.... then...
  3. The wiring haness is now exposed.
E) Wiring Harness

  1. You now un plug the wiring harness from:
  • Door handle
  • Lower courteosy light
  • Electric window controls (three wires)
F) Final steps

  • Lift the panel up and over the door lock button.
Now to your window problem.

When I examined the problem that I had with my Odyssey, I found the following:

  1. Two bolts were missing;
  2. The other tow bolts were lossed;
  3. The motor had shifted positions.





Nov 15, 2008 | 1995 Honda Odyssey

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

509 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...