The power steering is no longer working.I poured in additional fluid to the reservoir but this leaks out as soon as possible.
Secondly,the battery keeps runs down once its terminals are fixed to those of the car and parked overnight.The charging systems is perfect though.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
CAUTION: If the air is not purged from the power steering system correctly, premature power steering pump failure can result. The condition can occur on pre-delivery vehicles with evidence of aerated fluid or on vehicles that have had steering component repairs.
NOTE: A whine heard from the power steering pump can be caused by air in the system. The power steering purge procedure must be carried out prior to any component repair for which power steering noise complaints are accompanied by evidence of aerated fluid. Remove the power steering fluid reservoir cap. Check the fluid.
Raise the front wheels off the floor. For additional information, refer to Section 100-02 .
Tightly insert the stopper of the vacuum pump into the reservoir.
Start the engine.
Install the vacuum pump, apply vacuum and maintain maximum vacuum of 68-85 kPa (20-25 in-Hg).
CAUTION: Do not hold the steering wheel against the stops for more than 3 to 5 seconds at a time. Damage to the power steering pump can occur. Cycle the steering wheel fully from stop to stop 10 times.
Stop the engine.
Release the vacuum and remove the vacuum pump.
CAUTION: Do not overfill the reservoir. Fill the reservoir and install the reservoir cap.
Visually inspect the power steering system for leaks.
If you can't find a power steering fluid reservoir under the hood in the engine compartment your G6 could have Electronic Power Steering . If you look up under the dash below the steering column you will see a electric motor mounted to the steering column !
The power steering system reduces the amount of effort needed to steer the vehicle. The system uses the powertrain control module (PCM), body control module (BCM), power steering control module (PSCM), discrete battery voltage supply circuit, steering shaft torque sensor, steering wheel position sensor, power steering motor, driver information center (DIC), and the serial data circuit to perform the system functions. The PSCM and the power steering motor are serviced as an assembly and are serviced separately from the steering column assembly. The steering shaft torque sensor and the steering wheel position sensor are not serviced separately from each other or from the steering column assembly. The steering column assembly does not include the power steering motor and module assembly.
It means the power steering pump is no longer operating and so providing the required power assistance.
You either have a power steering fluid leak in the system and much of the fluid has been lost or the power steering pump itself has failed. You should not try and drive the car when you have this problem because the steering will be far too heavy to drive safely and because if a fluid leak has run the pump nearly dry you will cause damage to the PS pump.
The first thing to do is check the power steering fluid reservoir in the engine compartment. If it is low or empty you have a leak in the system. You can refill the system with new fluid but it will continue to leak until the leak is addressed and you will have to constantly add new PS fluid. In the case of a major leak the car will not be driveable as the PS fluid will be lost very rapidly. Without fluid you will quickly ruin the pump and you will also have no power assistance in your steering.
The power steering reservoir (I believe) is on the drivers side just behind the headlight. about mid-way down the side of the reservoir are a high and low mark. The reservoir should be just at or below the high mark when the vehicle is off. ONLY USE HONDA POWER STEERING FLUID. There are certain conditioners and additives in the Honda fluid that keep seals in the system in good condition. Using a generic/aftermarket fluid will cause the seals to shrink and the system will likely develop leaks.
First thing you need to do is remove thwe return line from your power steering reservoir. Thats the thing you put the power steering fluid in. Run that hose to a large container where you can catch a lot of fluid in. Now you want to make sure you have your new power steering fluid on hand before you start and another person would be very helpful also. Have your helper start the car and turn the wheel back and forth while you pour power steering fluid in the reservoir. Do not let your power steering fluid run completely out you can ruin your pump and or steering box. Continue to pour in new steering fluid until the fluid coming out of the hose thats in the bucket is clean fluid. Turn vehicle off reconect the hose to the reservoir and top off. With the lid off reservoir start the vehicle back up and turn wheel all the way back and forth many times(do not turn it to its furthest position where it bumps) continue to make sure the fluid level is always full. By turning the wheel back and forth you are bleeding the lines to get all the air out. Do that a few times, refill and put the cap back on. You just changed your power steering fluid. I f your vehicle is old you may want to get new rubber hoses for your power steering system. hoses degrade over time and eventually they start to flake off into your fluid which can damage parts. Always a good idea to replace hoses especially if they are soft.
YOU HAVE A RUPTURE PRESSURE LINE IF YOU HAVE NO POWER STEERING FLUID IN THE POWER STEERING RESERVOIR.LOCATE LEAK THEN BLEED POWER STEERING SYSTEM BY ADDING POWER STEERING TO RESERVOIR.DONT OVER FILL BY FULL COLD MARK ON POWER STEERING DIP STICK.ADD FLUID TO RESERVOIR WAIT A 2 MINUTES.CHECK FLUID LEVEL AGAIN.WHEN POWER STEERING FLUID LEVEL STOP DROPPING.START ENGINE LET IT RUN FOR 10 SECONDS.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID ADD FLUID IF FLUID LEVEL DROPS. WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE SUPPORT VECHICLE FRONT WHEELS.START ENGINE.NOW TURN STEERING WHEEL GENTLY FROM STOP TO STOP MEANING LEFT TO RIGHT DONT HOLD IN POSITION.LET THE STOP TO STOP BE QUICK.CHECK POWER STEERING FLUID AFTER YOU HAVE TURN STEERING WHEEL ABOUT 7 STOP TO STOP.WHEN FLUID LEVEL STOP DROPPING YOU AT HOT MARK ON DIP STICK BLEEDING PROCESS COMPLETE.TURN OFF ENGINE LOWER VECHICLE BACK TO GROUND WAIT ABOUT 5 MINUTES CHECK YOUR FLUID LEVEL.IF FLUID LOOKS LIKE A TAN COLOR.YOUR POWER STEERING SYSTEM FULL OF AIR.TURN OFF VECHICLE LET VECHICLE SET A LONG WHILE TO AIR BUBBLES SETTLE DOWN LOOK FOR LEAKS AROUND POWER STEERING PUMP FRONT SEAL AND CHECK FOR LEAKS AROUND POWER STEERING LINES.
Many "pour in" chems are harsh and will not only swell the seals you need swelled but ALL seals. I have had a lot of success with Lucas additive. It seems not be as harsh as other products and is a good lubricant and conditioner. I recommend you drain the system if possible to get rid of as much old oil and contamination as possible to prevent additional wear as well.
What you hae to do is check if the reservoir is leaking first if okthen it is either the piping or the steering pump. It is a process of elimination, you may need to clean the area first to discover where the leak is or work back from the point it is leaking on the belt. Until you identify where the leak is coming from it will be dificult to repair unless you just start to replace the pump and reservoir any way.