Question about 2005 Mitsubishi Lancer Evolution

1 Answer

Diff Removal What is the best and easist method to remove the front and rear diffs from my Evo 4 which require overhaul? Thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Take gearbox and transfer box out and take d sub frame out,i took mine out the other day 3 and half hours had them out

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear diff from ve commodore?


loosen rear wheels, jack up rear so wheels are free, fit safety stands , drain oil, remove wheels, remove 4 bolts holding axle bearings. remove both axles, remove bolts from tail shaft at diff pinion flange , leave tail shaft in transmission housing or oil will leak out, remove bolts from diff housing, the diff center can now be removed.

Aug 28, 2014 | 1998 Holden VT Commodore

1 Answer

96 pajero auto no power front right wheel i 4wd trans fluid level ok


wd diff lock only locks the front to rear diffs not the 2 wheels on the same diff. To have both front wheels driving as you require will need limited slip diff in front or locker in front Be hard to steer in tight areas but they are available.

Apr 22, 2013 | Cars & Trucks

1 Answer

How do you remove rear axle from 1995 ford ranger 2 wheel drive need to replace oil seal


Raise the vehicle and properly support it. Remove the wheel and drum. Remove the rear diff cover, have a drain pan underneath to catch the gear oil. Place the trans in nuetral, chalk the front wheels to keep vehicle from moving if you forget to put it back into park befor you lower the vehicle. Rotat the differential until you see the bolt that holds the diff pin in place. Remove the bolt, 5/16 or 8 mm I believe. You can then remove the diff pin, do not rotate the diff with the diff pin removed! Push the axle in, you can then remove the C-clip that holds the axle to the side gear, it will usuall drop or just fall out. Pull the axle out of the rear diff and replace the seal. Put everything back together. Use black or grey RTV to reseal the diff cover making sure o clean up both surfaces as best you can. Put trans in park. Lower the vehicle. Remove the fill plug from the side of the differential and fill with gear lube until lube comes out the hole. Reinstall the plug and your good to go. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Mar 15, 2012 | 1995 Ford Ranger Supercab

1 Answer

I had a leaking rear diff cover so I dropped the oil and clean the cover and the rear diff where the cover mates up and silconed the cover and reinstalled and then it start leaking out the front of the...


If the seal is leaking, it will need to be replaced, if you have a service manual, it will show you the procedure to replace the seal. DO NOT try to replace the seal without following the proper guidelines as input bearing damage can occur. After the repairs are made, be sure to to clean the vent tube/valve on the diff. to avoid pressure build up that will cause early seal failure, this vent should also be cleaned at every oil change.

Aug 16, 2011 | 2000 Dodge Durango

1 Answer

Front and back berring dissassembly of differential 2001 dodge 1500


For the rear diff., remove the driveshaft, brake drums, diff. cover, remove pinion flange nut, move diff carrier to access side gear retainer bolt and remove bolt, slide side gear pin out and push axles in to remove axle retainers and remove axels. Mark carrier bearing retainers, spin bearing retainers to loosen carrier for removal. Remove carrier, remove pinion out of diff case, then r&r bearings. Any shims should be replaced in their original location for depth and pinion to ring contact.

Feb 05, 2011 | 2001 Dodge Ram 2500 Truck

1 Answer

Small leak from rear diff. on my 96 ram 2500 4x4. is this something that i can fix myself?


if the leak is from the rear portion of the diff, often it can be cured by removing the cover, cleaning the mating surfaces, resealing and reinstalling. if the cover seems to have excessive corrosion inside, replace it. they are relatively inexpensive and available at almost any parts store, but original dodge ones from the dealer fit the best.

if the leak is from the front portion of the diff (front seal), this requires a some work beyond the scope of most home mechanics, but is not usually a very expensive job. good luck!

Oct 06, 2010 | 1996 Dodge Ram

1 Answer

Rear differential leak?


leaking where? axle shafts? pinion seal? diff cover?
should inspect diff internals and bearings-may require overhaul not just
seal replacment. also check vent tube-if plugged will cause all seals to leak.

Apr 15, 2010 | 1990 Ford Bronco

1 Answer

Front u joint on 1992 ford 4 x 4 trucks


the only way to remove the u joint from the latern ring is to remove the axle's this requires the removal of the diff cover and the axle keepers removed from the diff then they slide out (well they might require some forcefull help ) but the good news is if you support the end you don't need to remove it all the way

\just a tip after you get this fixed when you go thru mud or high water carry a small jug of clean water and give the grease seals a good splash to wash em out when you get back to the road
fords grease seals are a bit less than desireable for keeping out water /mud and cause the early demise of the u/joints i've even seen it as far as inside the diff but thats an extreeme Mudder

Sep 26, 2009 | 1994 Ford F350 Crew Cab

2 Answers

Need instructions for removal and installation of front u-joint on 1989 gmc jimmy


buy manual, removal:  raise vehicle and place on jack stands remove skid-plate, mark relationship of driveshaft to the front diff flange and the transfer case flange, remove the bolts and straps from diff flange and trans case flange, push the rear half of the driveshaft forward far enough to separate it from the transfer case flange, then lower it and separate it at the diff flange. installation: attach the front end of the driveshaft to the front diff flange and install the straps and bolts finger tight, extend or compress the driveshaft as necessary , attach the rear end to the transfer case flange, install the straps and bolts and tighten all bolts to 59 ft #'s , install skid plates, and lower vehicle 

Sep 12, 2009 | 1992 GMC Jimmy

1 Answer

Rear Axle Removal


if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

May 29, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...