Question about 2002 Ford Windstar Cargo

1 Answer

Serpentine belt power steering pump screeching after new pump and belt installed belt configuration wrong?

Posted by on

  • elitecreatio Sep 03, 2008

    no not before but after Thanks for the response

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Possibly. was ir screeching before you replaced the belt?

Posted on Sep 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Screeching noise coming from belt area. just replaced powere steering pump & belt & this started.


The screeching is the belt slipping, two possibilities, either the belt is not tight enough, or you have fitted a faulty pump which is putting to much resistance on the belt? If it carries on screeching for any length of time it will break. Check your alternator belt tension, if you had to remove and refit that? Quick check for alternator belt is, switch on headlights, does the screech get louder? Don't over tighten the belts, this puts stress on bearings!

Dec 27, 2013 | 1999 Dodge Grand Caravan

2 Answers

The whining sreaching sounds under the hood starts when you 1st started then after that somtimes gets louder while you driving only


Could be a pulley, belt or bearings of sort. Take it to a well referenced repair shop for proper diagnostics.

Oct 09, 2013 | 2003 Chevrolet TrailBlazer

1 Answer

I replaced the serpentine belt and now have a terrible screeching with the a/c is turned on.


A couple of things come to mind: if it wasn't screeching before replacing the belt, you may not have routed the belt properly - especially around the belt tensioner pulley; or the bearing on that pulley may need lubrication or replacement; or the A/C compressor bearing may have failed causing excessive resistance on the new belt resulting in screeching. Also, if the belt was not routed properly, the screeching may be coming from another belt-driven (power steering pump, water pump, etc.) but it doesn't sow up until you engage the A/C with its additional drag.

Sep 28, 2013 | 2003 Toyota Avalon

1 Answer

If a power steering pump locks up does it have to be replaced?


the power steering pump locking up is the reason ur serpentine belt broke. on front of power steering pump is a pulley which must spin freely. when this pulley locks up, things break...and yes u definitely need a new power steering pump.

Feb 06, 2013 | Ford Ranger Cars & Trucks

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

Every time I turn on the air or heat when the car is running My power steering iseffected and a loud screech? But not when the car not running (blower motor works) I think it is the ac condencer?


you need to replace the serpentine belt and perhaps the belt tensioner. When a heavy load is put on the belt, like turning on the AC, the drag may stop the belt from turning. This would stop the power steering pump from turning causing a hard steer condition. The belt is not gripping the pulleys tight enough. This is due to a worn out serpentine belt or worn out tensioner. If the AC works( cools the car) then replace the belt. If this does not cure the problem then replace the belt tensioner as well.

Nov 19, 2010 | 1998 Plymouth Neon

3 Answers

1989 GMC Jimmy Serpentine belt diagram for an idiot, please!


sounds like you got something thats tied up, like an ideler polly, or the spring tennsioner polly, or maybe even the alt. or power steering pump. Did you follow the routing diagram on top of the fan shroud?

May 07, 2009 | 1988 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...