Question about 1992 Geo Tracker

3 Answers

93 GEO TRACKER

TURNS OVER .GETTING FUEL GOT SPARK,TIMING BELT IS ON,WHAT COULD IT BE 94 geo tracker ,new head ,did not remove old gear shop did,has to positions can be mounted on cam gear,and #1 tdc which way does the pin in cam for gear position.put together several ways already would not run,blows fuel out carb. 1.6L

Posted by on

  • groo1 Sep 03, 2008

    thanks ,cant remember if i change it or not but ill start over with the pin up.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Take the number 1 spark plugh out of the head. turn crank so the piston is in =TDC (you can use a 1/4 drive extension to feel the top of piston) take the cap off the distributor the rotor should be pointing in the #1 fire position... check this and let me know

Posted on Sep 02, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,028 Answers

I believe the pin should be positioned at the top, but I'm not 100% on that. I'm going to say that the position you had when the fuel backed up into the carb is 180 degrees out on the cam, and that the valves were opening during the compression stroke, therefore blowing the fuel back instead of pulling it in. If you know where the gear was during this, then take it off, go a complete 180 degrees with the cam, and put it back on. This should get you close enough to for the engine to start, then you'll need to dial it in.

Posted on Sep 02, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 521 Answers

Check all of the battery terminals and cables and check the wires on the starter/selonoid, start from the battery and follow the cable out and check all conections , clean and tighten them and if it still does it the starter/selonoid is bad and needs replacement...

pls do rate the solution

thanks.
regards.
fixya expert team

Posted on Sep 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have a geo tracker repair manual


there are 2 engine. 8v and 16v TBI or MPI
both here.
see main Menu here.

http://www.fixkick.com/t-belt/tbelt-index.html

both fsm pages, and full steps, with photos way

Sep 04, 2014 | Geo Tracker Cars & Trucks

1 Answer

Crank and cam postions 94 geo tracker 16v engine


cam timing this is called, on the G16b 16v not 8v.
easy
old post , and common 60,000mile service question.,
see the false cam marks, avoid them !!!

http://www.fixkick.com/t-belt/16-fast-belt-install.html

Jan 15, 2014 | 1995 Geo Tracker

1 Answer

Just did a top end new valve seals head gasket laped the valve seats went back togather with it timing marks lined up it wont fire realy confused want to know if 1995 Geo Tracker needs the alternator or...


no u dont need them hookd up to run u do need to see if ur getting inch to inch half spark if ok check vakve movment see if to tight and lifters not pumping up and if all else fails new plugs cut the fuel if dont start call me im at my shop 6 days a week i just done same to one was kinda stuborn on start p 8016865205

Oct 26, 2010 | 1995 Geo Tracker

1 Answer

I have a 1996 geo tracker 16 valve rebuilt a 1990


your timing may be off because of the valve timing. have you seen this done before or you just trying your luck. i really dont know but are all of your sensors the same? is the firing order the same?

Nov 10, 2009 | 1991 Geo Tracker

3 Answers

I need a diagram of engine timing marks for a 1.6 litre engine


1996 Geo Truck Tracker 2WD 1.6L MFI SOHC 4cyl

2efa731.jpg

Fig.: Before installing the timing belt, position the camshaft sprocket (1) so that the timing mark on the sprocket (2) is aligned with the notch (3) on the inside timing belt cover (4) ...

5a2ee07.jpg

Fig.: ...and ensure that the crankshaft sprocket (1) timing mark (2) is aligned with the mark on the oil pump (3)

For more details, can register in autozone.com (free).

I hope help you with this (remember rated this help) Good luck.

Oct 15, 2009 | 1996 Geo Tracker 2 Door

1 Answer

1992 geo tracker will not run


The ECM has a blown capacitor inside it for opening the injector you will most likly need to get it rebuilt, buy a new ,or used ECM had the same problem with my sidekick.

Mar 16, 2009 | 1992 Geo Tracker

2 Answers

WON'T START


Check compression if its good, Check timing

Dec 30, 2008 | 1996 Geo Tracker 2 Door

2 Answers

My 1990 geo tracker wont start


STARTER RING GEAR, TEETH MISSING?

Oct 07, 2008 | 1990 Geo Tracker

1 Answer

93 GEO TRACKER


is it fuel injected ot carburated?

Aug 29, 2008 | 1992 Geo Tracker

Not finding what you are looking for?
1992 Geo Tracker Logo

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...