Question about 1991 Mitsubishi Mirage

2 Answers

How to reset ecu unit for a 1990 mitsubishi mirage

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I dont know about the mirage but 9 out of 10 cars all you have to do is unplug your battery for at least 5-15 minutes and then re plug in and start car. your check engine light/ecu should be reset now. Good Luck and God Bless. Hope this helps. Take care. 16

Posted on Nov 20, 2008

I don't know

Posted on Oct 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1998 mirage i recently replaced ecu ignition and imobilizer module it now runs but sounds louder than before it seems like a deeper note at air box and just dont seem the same could it be ignition...


This could be different programming of the new ECU. You might also need to get it tuned with the new ECU. It could have changed the ignition timing.

Mar 10, 2015 | 1998 Mitsubishi Mirage

2 Answers

I am trying to reset the srs light on my 1996 Mitsubishi colt. I have replaced the airbag and rotary switch(springs behind wheel) but cannot seem to locatate my airbag ecu. Where is the location of my...


If the airbag has been deployed, is is necessary to REPLACE the airbag (SRS) ECU. It is located below the center console. (See picture) It must be replaced because on your vehicle, it contains the crash sensors. If you do not replace it and hook-up new airbags and turn the key on, the new airbags will immediately deploy. There is no way to "reset" it.


dttech_92.gif

May 24, 2011 | 1996 Mitsubishi Mirage

1 Answer

Bottom pully. 1990 mit mirage wagon . i have tried with a air gun but it still won't budge.


are you turning it the right way, most harmonic balancer bolts are backwards thread, if you have tried both directions put a socket and breaker bar on the bolt then rest the breaker bar (still attatched to the bolt) against the chassis and then turn the car over with ign, the bolt always tightens against the rotation of the engine so the turning of the starter motor will undoo the bolt for you. hope this has been helpfull.

May 16, 2009 | 1990 Mitsubishi Mirage Hatchback

1 Answer

Replace fuel pump 1990 mits mirage


no but you do need to remove the back seat to unplug the fuel level sending unit wires before dropping the tank.

Feb 28, 2009 | 1990 Mitsubishi Mirage Hatchback

1 Answer

Diagnostic code suggests that idle air control motor defective explain


HI
firstly what is the number of diagnostic code?? (P0???)
the (IAC)idle air control motor locate in the engine near the intake manifold it have a 6 pin connector:-
the 2 & 5 is 12 volt supply from fuse box
the 1,3,4&6 is from (ECU) engine control unit
it function is control the idle speed of engine

WITH MY BEST WISHES

Jun 20, 2008 | 1997 Mitsubishi Mirage

Not finding what you are looking for?
1991 Mitsubishi Mirage Logo

Related Topics:

1,246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...