Tip & How-To about Jeep Grand Cherokee

1993 jeep cherrokee alarm disabling

Start engine,remove overhead panel unplug the harness to the sensor then remove glove box and panel behind it then unplug black box that says secuity on it , you will never have an alarm after that ,

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

where is the security box on 1993 gran cherokee located


Security Alarm Module is located in rigt side box of glove box (attached image) from Repair Manual (Wiring Section).

3_22_2012_12_31_19_pm.jpg

Hope helps.

Mar 22, 2012 | 1993 Jeep Grand Cherokee

1 Answer

ecu removal instructions


That begs the question of WHY are you wanting to remove it?

Anyway, the ECM is located behind the glove box. Remove the glove box to get to the ECM to remove it.

Also please note that if the ECU is replaced, it must be programmed to work with the onboard secuity system - or the engine will not start and run.

Mar 05, 2012 | 2003 Toyota Camry

3 Answers

i need to disable my alarm on a 1997 bmw 528i.


Now im not sure since the manual says your model has the same alarm system as the 328i and on the 328i you can remove the module to disable by doing the following. you can unplug the control module. It is located under the glove box. Climb under the dash on the passenger side and remove a few screws on the trim panel under the glove box. Theres a black control module with a green connector. There should be a lock tab on the connector. press the lock tab and pull out the connector. The alarm should now be disabled. But if it has the special transponder key this may not work.
But if the only reason you want to disable it is because of the motion sensor setting of the alarm for no reason there is a solution for this. To disable the motion sensor, hit the lock button to arm, then hit lock button again within four seconds to disable motion sensor. Red light on rearview mirror should flash four times, then pause, then start flashing on regular intervals. this is most likely the reason if your having the issue where the alarm goes off every 20 minutes.
If you want to completely remove it below is a wiring diagram taken from the manual for you alarm system.
this is from the manual its the alarm wiring diagram.
Battery Constant 12v Positive Wire ( ): Red/White or RedBattery Constant 12v Positive Wire Location: Ignition Switch Harness
Starter Positive Wire ( ): Black/Yellow or Black
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire ( ): Green
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire ( ): Purple/White or Purple
Second Ignition Positive Wire Location: Ignition Switch Harness
Parking Light Positive Wire ( ): Gray/Purple and Gray/Yellow. Use Both Wires. This vehicle has a dual parking light system that will require 2 extra relays.
Parking Light Positive Wire Location: At Headlight Switch
Power Door Lock Positive Wire ( ): White/Red
Power Door Lock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Power Door Unlock Positive Wire ( ): Blue/Red
Power Door Unlock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Door Trigger Negative Wire (-): Brown/Gray
Door Trigger Negative Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Domelight Supervision Wire: Turns On With Unlock
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Brown/Red or Brown/Yellow
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Black
Tachometer Wire Negative Wire Location: At Instrument Cluster
Brake Light Positive Wire ( ): Blue/Red or Green/Red
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): Disarms With Factory Remote Only. Factory Alarm Disarm Wire Location: N/A
Factory Anti-Theft System: Transponder Anti-Theft System, Requires Bypass And Extra Ignition Key. The 1997 model year vehicle may require a bypass module and an extra ignition key, if vehicle is equipped with a special key from BMW.
Factory Anti-Theft System Location: Transponder At Ignition Switch Tumbler
if you require further assistance please let me know and i will help assist you from there. Thanks, Midwest-Tek

Aug 27, 2010 | 1997 BMW 328

1 Answer

my imoblieser wont go off if i tap on the glove box it goes off some times and i can start my car


Try this there is a fuse box behind the glove box are all the connectors tight. Also the main electrical harness runs behind the glove box All you have to do is remove the glove box D

Oct 23, 2009 | 2004 Jaguar X-Type

1 Answer

chevy trucks 1500 black box location


If you are talking about the PCM it is behind the glove box. Remove the glove box and you will see an aluminum box with a large wire harness going into it.

Aug 09, 2008 | 1993 Chevrolet C1500

Not finding what you are looking for?

1,138 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Loading...