Tip & How-To about Hyundai Tiburon

How to disable the alarm in the Hyundai 2003 Tiburon car without the remote?

The procedure is as follows:--

  1. Put the key in the ignition and turn to the "On" position.
  2. Leave it in that position until the alarm stops, between 30-120 seconds.
  3. Wait 30 seconds after that and start car.
This will help.thanks.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

How do I reset security system on my 2000 Bonneville?


press the helpful button and follow me on fixya for more tips

Put the key into ignition and turn it to RUN position. All dash lights will illuminate. Don't try to start the car. Leave the key in the ignition for about 5-10 minutes or until security light will stop flashing. The car should start after that. Security lock on the Pontiac disables the injectors, so the engine should crank. If it does not, you may want to check ignition switch, fuse and relay for the starter. Try to reset security first. Sometimes the magnet in the ignition lock cylinder gets dirty and needs cleaning. written by AlexGS
If the above procedure does not work the first time, try again, but right at the start insert key in and out of ignition several times to get good contact, as your key or ignition could be faulty.

Passlock III reset procedure reset security system on chevy buick...

https://ca.answers.yahoo.com/question/index?qid=20080809211716AAHluay

Feb 01, 2016 | Cars & Trucks

1 Answer

where is the shut-off switch for tundra alarm


Hi, I am not sure where the switch is but 3 months ago the following was posted by:-


liverhuyen2003 answered 3 months ago
Make sure the drivers front(left front) door is closed and you have your car keys. Insert your door key into the drivers door and turn it to the locked position two times. Then turn the key to the unlock position twice. The alarm should be disarmed, now.

SECOND TECHNIQUE: If not then take the ignition key and turn the ignition switch all the way ON then OFF then ON a second time and OFF again. These are the procedures for nearly all factory alarm systems. If neither of these works you probably have an after market(add-on) alarm system.

Warnings This technique is only for use on your own car that you own and have keys for. If you don't have the keys- disconnect the negative battery cable to stop the horn until you get your keys. Then reconnect the negative terminal and proceed to step one.

Hope this helps!

Apr 06, 2014 | 2001 Toyota Tundra

1 Answer

i can't turn off the security alarm on my 1998 nissan pathfinder


I couldn't turn off the security alarm on my 1999 Pathfinder as I replaced the battery,
Solution: I read the solution here to disconnect the positive cable, open the driver's door, insert the key, then reconnected the positive cable, while honking, I turn the key to the left, to the right and to the left again while the door is still open. The honking stopped. Then I started the truck without a problem. Thank you for the hint.

Jun 12, 2012 | 1998 Nissan Pathfinder

1 Answer

I replaced battery in my audi 80 2.0 tdi but have lost the remote and alarm wont stop going off .


Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction: Alarm LED in rear fog lamp switch illuminates for 30 seconds when vehicle is locked.
How
NOTE: A maximum of 4 keys can be programmed (one at a time).
As memory positions of existing keys are unlikely to be known: Obtain and reprogram all keys.
NOTE: Existing key memory positions will be overwritten.
Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Using first key, press unlock button once (programs memory position 1). Alarm horn sounds once to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF. To program remaining keys into memory positions 2, 3 and 4. Carry out the complete procedure below for each key: Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Press unlock button at 1 second intervals, as follows: Twice for memory position 2 (second key). Three times for memory position 3 (third key). Four times for memory position 4 (fourth key). Alarm horn sounds once every time unlock button is pressed, to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF.
NOTE: Ignition MUST be switched OFF between each key programming procedure

Jan 10, 2010 | 1992 Audi 80

Not finding what you are looking for?

2,969 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Loading...