Tip & How-To about Toyota Tundra

How to Replace a Radiator in a Toyota Tundra car?

The instructions to replace the radiator is as follows:--
1) Locate the radiator. For that remove the engine undercover. Beside the radiator there is a plug.Loosen the plug on the bottom of the radiator and drain the engine coolant into tray or bucket.Also disconnect the hose to the radiator reservoir, and take off the upper radiator hose and lower radiator hose
2) Then to remove the radiator.Look at the fan shroud and remove the bolts holding the radiator. Detach the clips holding the fan shroud and lift the radiator carefully out of the engine compartment.
3) The old faulty radiator which you want to remove is out now.
4) Put the radiator bracket hooks in the radiator support holes and install the new radiator in the reverse method of how you removed the old one out.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

how do you remove the alternator from a 2004 Nissan Maxma?


3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Right side engine undercover and side inspection cover
    • Radiator on Maxima
    • Radiator fan on 350Z
    • Drive belt
    • Alternator and A/C compressor harness connectors
    • Upper and lower alternator bolts
    • Alternator

Install or connect the following:

  • Alternator
  • Upper and lower alternator bolts. On Maxima tighten the upper bolt to 12-15 ft. lbs. (16 -20 Nm) and the lower bolt to 32-38 ft. lbs. (44-52 Nm). On 350Z, tighten the upper bolt to 48 ft. lbs. (65 Nm) and the lower bolts to 21 ft. lbs. (28 Nm).
  • Alternator and A/C compressor harness connectors
  • Drive belt
  • Radiator on Maxima
  • Radiator fan on 350Z
  • Right side engine undercover and side inspection cover
  • Negative battery cable
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 25; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 08, 2011 | 2004 Nissan Maxima

1 Answer

trying to remove an alternator from an 06 altima


Removal and Installation L4-2.5L (QR25DE) Engines To Remove:
nis_alt_l4_alt.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Engine cover
    • Front/right-side engine undercover
    • Drive belt
    • Alternator harness connector
    • Engine ground wire from top mount
    • Alternator upper and lower mounting bolts
  3. Set the alternator aside and remove the top mount.
  4. Remove the alternator.
To Install:
nis_alt_l4_alt1.gif

  1. Slide alternator in place.
  2. Install or connect the following:
    • Alternator top mount
    • Alternator upper and lower mounting bolts
    • Engine ground wire from top mount
    • Alternator harness connector
    • Drive belt
    • Front/right-side engine undercover
    • Engine cover
    • Negative battery cable
V6-3.5L (VQ35) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain coolant from the radiator into a suitable container.
  4. Remove or disconnect the following:
    • Radiator
    • Front/right-side engine under cover
    • Drive belt
    • Idler pulley
    • Alternator adjustable top mount
    • Alternator lower mount bolt and nuts
    • Alternator lower front bracket bolt
    • Alternator harness connectors
    • Alternator
To Install:
nis_alt_chg_v6.gif

  1. Install or connect the following:
    • Alternator in place
    • Alternator harness connectors
    • Alternator lower front bracket bolt
    • Alternator lower mount bolt and nuts
    • Alternator adjustable top mount
    • Idler pulley
    • Drive belt
    • Front/right-side engine under cover
    • Radiator
  2. Replace the engine coolant.
  3. Connect the negative battery cable.
  4. Start the engine and check for leaks.
  5. Recheck coolant level and top off as needed.
prev.gif next.gif

Oct 15, 2010 | 2006 Nissan Altima

1 Answer

How to replace the starter


Toyota Celica, Corolla, ECHO & MR2 1999-05
Starter - Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Radiator upper support seal
Air cleaner
Engine under covers
Starter wiring
Starter

3. Installation is the reverse of removal. Torque the bolts to 28 ft. lbs. (37 Nm). Note that the bolts are 2 different lengths.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Battery and tray. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery.
Coolant reservoir
Reservoir hose from the radiator
Right side under cover
Wiring clamp
Wiring from the starter
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring and nut
Starter connector and wire clamp
Right side engine cover
Radiator reservoir and hose
Battery and tray

2. Check the cooling system and top off if necessary.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery
Engine under covers
Wiring from the starter terminals
Starter mounting bolts
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring
Engine under covers


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable
Front engine undercover
Starter wiring harness connectors
Starter mounting bolts
Starter motor


To install:
1. Install or connect the following:
Starter motor. Tighten the bolts to 28 ft. lbs. (37 Nm).
Starter wiring harness connectors
Front engine undercover
Negative battery cable

Hope help with this (remember rated and comment).

Mar 11, 2010 | 2003 Toyota Corolla

1 Answer

cylinder head removal on 2005 nissan altima 2.5 engine would like to know how to remove the camshaft to remove the head bolts


CYLINDER HEAD REMOVAL

2.5L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Nov 13, 2009 | 2005 Nissan Altima

Not finding what you are looking for?

2,100 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Loading...