Tip & How-To about Oldsmobile Alero

How to Reset Oil Change Light

On the drivers side of the dash in the A piller area,Remove the fuse block cover push and hold the yellow reset button in with the key on engine off,until the change oil light starts flashing release button and light will flash a few more times and should go out.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

2000 Buick LeSabre: Check tire pressure warning is flashing, but tire pressure is OK


Have you tried resetting the light? On either the end of the dash on the drivers side or the end of the dash on the passenger side there is a panel that covers the fuse block. You'll need to have the door open to access it. Once you remove the cover you should see a button that says reset. Turn the key to the run position and press the button. The change oil message should flash, press the button again and the low tire message should flash, press and hold the button until the low tire light turns off. Sometime there will also be an audible series of beeps when it resets.

Jun 25, 2011 | Buick LeSabre Cars & Trucks

1 Answer

How do you reset the "change oil" light?


Try this procedure;

Locate the "Red" reset button towards the top of the fuse panel, in the fuse panel on the side of the driver side dash. (Open driver side door and remove the fuse panel cover to access the fuse panel and the reset button)

1. Turn the ignition key to the "On" position, but do not start the engine.

2. Press and hold down the "Reset" button until the "Change Oil" light starts flashing.

3. Then press and hold down the "Reset" button again until there is a chime or beep(s) and the "Change Oil" light should then go out.

4. Turn off the ignition, and then start the vehicle and confirm that the "Change Oil" light has been reset.

(May have to repeat the procedure to be successful)

Let me know if this procedure did not work for your vehicle as there are other procedures and depending on the type of system that is being used.

Nov 24, 2010 | 2001 Oldsmobile Alero

3 Answers

2001 pontiac grand am oil change light wont go out


Do the following steps
1)With ignition key on. ( a shrt time after turning off engine) press the red reset button located in fuse panel , located on drivers side of dash panel. You can see the panel cover when drivers side door is open.
2) When the cange oil light starts to flash, press and hold the red button again.
the reset is complete when you hear the chimes and the oil light goes off.
Reply if this was helpful

Feb 12, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Just got an oil change but the "oil change" light is still on, how do I reset it?


drivers side fuse block, remove cover
1.turn key on (engine off)
2. push the reset button in
3. change oil light will start to flash, press and hold reset button again, reset is complete when you hear the chimes sound and the change oil light goes out

Feb 05, 2010 | 2000 Oldsmobile Alero

3 Answers

change oil light remains on after oil change and light over license plate does not work after bulb change


To reset the Change Oil Light: Open driver's door and open fuse access panel
Turn ignition key to on (don't crank the starter) Push reset button located in fuse panel When Change Oil Light starts to flash Press and hold reset button until it beeps and light goes off Repace panel

Jul 17, 2008 | 2003 Oldsmobile Alero

Not finding what you are looking for?

1,236 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Loading...