Tip & How-To about Dodge Challenger

How to change you oil for any car.

Jack ur car up(get a jack put it in the folds of msa car you'll see em there rite next to the cars wheels then put stands their. do that on all four side). then get an oil pan then locate ur oilbox
(its the big black box that usualy under ur engin) then unsrew the bolt that is attached to it ( WACH OUT OIL WILL COME OUT SO DO IT FAST) then let ur oil drain then remove ur filter this is the hardist for me becasue the filter is always located some where differint on every car look. you should look under ur car it looks like a cylinder but short and fat. then unsrew that then let it all drain usualy five minits o and throw the old filter away. then go get new oil and oil filter calledvalvoline (I SAY VALVOLINE BC THE WLLMART BRNDS ARE CHEEP BUT CRAPY AND WILL ACTUALY HURT UR ENGIN BC THE GAT CARBOARD IN THERE I THINK U KNOW WHAT IT WILL DO TO YOUR ENGIN U CAN GET IT AT A NAPA). Then get an owners manual for ur car wile ur at napa then find the rite oil messure screw back the skreew make sure not to strip them take some oil put it around ur oil filter ruber ring then srew that back on fill up ur oil strat your car then turnit off after 30 second check oil level if its at good or above the fill line then your good to go.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

toyota hilux surf 1996. how could i know if im stuck in four wheel drive?


Jack up the vehicle on anxle stands start the car put in gear if all wheels turn in all gear settings then yes you are.

Jul 21, 2014 | Cars & Trucks

1 Answer

how to remove rear wheel hub


first set the parking brake, then loosen lug nuts all but one to keep wheel on, just loose so that after you jack up the car you can remove it, after car is jacked up put a jack stand under it to support it, now remove the wheel, once car is on jack stands, release the parking brake, next you will have to remove the wheel hub, do not take off any brake parts, they will not be in the way, next, look on the back and you will see 4 17 mm bolts, these hold the hub assembly on to the carrier, once off , reverse the way you took it off, doing the other side as the same

Feb 23, 2014 | 2005 Scion xB

2 Answers

a womp womp womp noise in the rear, tires are good, brakes look good, wheels are not warped, just had them balanced?


Go to a place that has a good smooth parking lot and a wooden private fence. Open all your windows and drive the car slowly as close as possible along the fence in order to pin point where the sound is coming from. The sound will echo back from the fence and will make it easier to pin point the area where the womp womp sound is coming from. Next thing you can do is lift the car up and place it on four jack stands in case you have a front wheel drive. If you have a front wheel drive and your car is on four jack stands, place you gear in nuetral and spin each rear tire separately to see which one is making the noise. Keep in mind that it might be a wheel bearing or if it a rear wheel drive and on four jack stands have someone drive it slowly while you listen for the noise. Some rear wheel drive differentials can make this noise if it is low on differial oil. Be very careful that the jack stands are on solid and making good contact with the car frame and flat on the pavement. Don't place yourself where the car can fall and hit you or run in to you. Good luck.

Dec 03, 2012 | 2002 Porsche Boxster

1 Answer

wont shift out of 4wd


If rear end is up in the air only. And it turns. Then know its not in four wheel drive. If u put the rear end up on jacks and leave the front end on the ground and then put it in four wheel drive its going to pull the truck off the jacks Danger. Does the truck try to come of of the jacks. If yes then its in four wheel drive. Should also be a lite on the dash. Saying 4 wd

Jun 13, 2012 | 2000 Ford Explorer

1 Answer

wheel stud replacement


very easy remove wheel support car on jack stands take hammer and beat the old stud out put new stud in place thick metal washers on stud titen lug nut on stud until stud is all they way in place replace wheel and ur all done

Apr 21, 2010 | 1997 Honda Accord

Not finding what you are looking for?

1,353 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Loading...