Tip & How-To about Ford Fusion

How To Change A Car Battery

This Tip describes the correct procedure for changing a car battery.These steps apply equally if you intend to remove your old battery for recharging and then replacing it into the vehicle. Changing a battery is a straightforward process as long as you adhere to the correct procedure. This Tip includes some photos to help aid the process.



Common cautions to be aware of before commencing;

Caution 1: Rubber gloves and protective eye goggles should be worn during this procedure as car batteries contain a sulfuric acid electrolyte solution. This is highly corrosive (i.e. can burn your skin) and produces a flammable gas. Do not smoke and keep naked flames away from the work area. Do not touch any old corrosion on the terminals with bare skin. Be careful when handling car batteries - they are heavy - always keep them reasonably level when handling them to prevent any acid spillage occurring. Battery terminals contain lead - always wash your hands after completing this procedure.


Caution 2: Be careful not to cross over the connections to the battery. Red (+) is positive and goes to the (+) Terminal on the battery. Black (-) is negative and goes to the (-) Terminal on the battery.

  • When removing the battery - always remove Negative Terminal first.
  • When replacing the battery always replace Positive Terminal first.

Caution 3: Modern vehicles will have a number of presets that depend on a connection to the battery e.g. stereo, electric seat memory, Sat Nav. etc... For this reason it is recommended to use a memory keeper to avoid any complications that may arise from disconnecting your old battery. A memory keeper simply plugs in to your vehicles cigarette lighter or accessory socket and maintains power to the vehicles accessories whilst you disconnect your old battery. Memory keepers can be powered by the mains supply or some require another 12v battery or 9v battery as a power source - so be sure to purchase one that suits your needs.

You can perform this procedure without a memory keeper but please ensure that you have all the relevant security codes you need in order to reactivate your stereo or any other accessories that will require a PIN code. If in doubt refer to your vehicles handbook.


1) Gather together the tools you need for the job.
  • Your new battery which meets the specification of your vehicle.
  • Wrenches/Spanners for loosening and tightening the nuts on the terminal clamps.
  • A wire brush and sandpaper.
  • Memory Keeper (as described).
  • Vaseline or Battery Lithium grease.

2) Make sure the vehicle is parked on level ground and secured by the handbrake.

3) Familiarize yourself with the instructions with your memory keeper and then plug it in to the cigarette lighter socket.

4) From under the hood identify the battery terminals and clamps. The negative terminal (or battery post) on top of the battery will have a minus (-) sign beside it and the positiive terminal will have a plus (+) sign. In addition to labelling (like on the battery below) these signs will also be indented into the plastic on the top of the battery beside the battery posts.




5) Remove the negative terminal clamp first - using your wrenches loosen the nut (circled below in red) and remove the negative terminal clamp. Removing the negative terminal first helps to avoid any short circuit occurring during the procedure. See below an example of a negative clamp with identification marks circled in black.



6) Next remove the positive terminal clamp.

7) There will be a battery locking mechanism holding the battery in place and clamping it to the vehicle - usually a metal bar. Remove this and then carefully remove the old battery.

8) Next clean the terminal clamps and the battery tray using the wire brush. You may also use some fine sandpaper to clean the inside of the clamps. Make sure you are wearing the safety gloves and goggles during this procedure. Remove as much corrosion and dirt as you can. This helps ensure a good connection to the new battery when you reconnect.

9) Put your new battery in and secure it to the vehicle with the locking mechanism.

10) Reconnect the battery by attaching the Positive terminal first and tighten the clamp with your wrench until you have a good tight connection.

11) Reconnect the Negative Terminal and secure as above.

12) Once the connections are made, you may coat the terminals with ordinary Vaseline or Battery Lithium grease to help prevent further corrosion.

13) Remove memory keeper from cigarette lighter socket. Shut the hood and the job is done.

Hope this Tip has helped. Please do reflect the usefulness of this Tip by using the Yes/No Voting buttons below.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

2 Answers

step by step instructions on removing intake manifold on 1992 buick roadmaster limited


  1. On models equipped with airbag, disable airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING .
  2. On all models, disconnect battery ground cable, drain cooling system and remove air cleaner.
  3. Disconnect accelerator, transmission and cruise control linkages, as equipped.
  4. Disconnect fuel line from carburetor or TBI unit and remove fuel line clips as needed, then remove carburetor or throttle body from intake manifold.
  5. Disconnect necessary vacuum hoses and electrical connectors, noting position for installation.
  6. Disconnect upper radiator and heater hoses from manifold.
  7. On Cadillac Brougham models, remove thermostat and housing.
  8. On all models, remove distributor.
  9. Remove ignition coil, AIR pump, cruise control servo and brackets, as needed.
  10. Remove alternator upper mounting bracket and EGR solenoids.
  11. Remove manifold retaining bolts and the manifold.
  12. Reverse procedure to install, noting the following:
    1. Ensure surfaces are clean and dry, then apply 3/16 bead of RTV sealer on each block ridge and apply suitable sealer around water outlets, install gaskets and secure gasket position by extending bead of sealer approximately 1/2 inch onto gasket ends.
    2. Install manifold and retaining bolts, ensuring areas between case ridges and manifold are completely sealed.
    3. Torque manifold bolts to specifications in sequence shown in Figs. 2 and 3.
    4. After installing carburetor or TBI unit, check to ensure no fuel leakage is present.
  1. Rearm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING

Jul 21, 2009 | 1992 Buick Roadmaster

1 Answer

how do you replace a water pump in a 1997 jeep grand cherokee laredo?


Hi there Ramarob

Here's a step by step to remove and replace the water pump on your Cherokee.

Be advised, all 4.0L engines, some 2.8L engines and some 4.2L engines have a reverse rotating water pump. You can ID these from the word REVERSE or REV imprinted or cast on the housing and/or fan. There will also be an 'R' stamped into the impellor.

Make sure your replacement pump is the correct type, If not, expect some major turmoil.

The procedure:
1. Remove negative battery cable
2. Open radiator valve - drain cooling system2.gif
3. Remove cooling fan2.gif and shroud
4. Remove belts (see my tip on serpentine belts if needed)
5. Remove water pump pulley from hub
6. Remove hoses from water pump
7. Remove accessory brackets from the water pump.
When removing the P/S pump and/or AC compressor, leave the hoses attached and move them out of the way.
8 . Remove the remaining bolts and detach the water pump from the engine. The bolts are three different lengths. Make note of where they came from.
9. Compare the new and old pumps. Make sure they match.
10. Scrape off the old gasket material.
11. Apply a thin continuous line of RTV High Temp sealant to the water pump side of the gasket.
12. Put a couple bolts through the pump to hold the gasket in place and mount the gasket.
13. Apply Another coat to the other side of the gasket.
14. Attach the pump to the engine. Screw the bolts in finger tight.
15. Attach the remaining bolts.
16. Tighten them up in 1/4 turn increments.
17. Re-attach all the stuff you removed
18. Refill the coolant, adjust belt tension.
19. Run the engine and check for leaks.

Hope this is very helpful
Mike

May 05, 2009 | 1997 Jeep Cherokee Country

Not finding what you are looking for?

5,069 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Loading...