Tip & How-To about 2007 Toyota Sienna

Sienna van door checks need repair

If you own a toyota sienna van 2007 and up and are hearing a clicking noise when you open your frount doors you need to go to your dealer and have your door checks repaird . door check is the arm that holds your door and keeps it from opening to far. don`t wate to long they will do a lot damange if not taken care of.and Toyota will pay for it.

Posted by on

2007 Toyota Sienna Logo

Related Topics:

Related Questions:

1 Answer

I have 2002 toyota sienna XLE. I can use key to control the power sliding door opening and closing when the door is not closed. However, when the door is close, I can not use key to control it. I can only hear some noise, but I touch the door handle twice, it will be automic opening.


the noise you can hear is the lock/opening actuater, have to strip out door panel and see if the actuater mechanism is intact, and operate as before and look to see what part is trying to move, it may just need lubricating but be prepared to have to have new lock actuator

May 03, 2014 | 2006 Toyota Sienna

1 Answer

rear door on 2001 sienna won't open


The door handle might be broken, you need a new part. I got mine online for $40. keywords: 2001 2002 2003 2004 2005 2006 2007 Toyota Sequoia Metal Lift Gate Exterior Door Handle for Rear Outside Van Tailgate Handle. You need to remove the back door panel to replace this.

Mar 06, 2010 | 2001 Toyota Sienna

1 Answer

2007 toyota sienna ce ,In dash board tiers low pressure light


sorry no quick fix ,fault with electrics ,encrypted software dealer only

Oct 24, 2009 | 2007 Toyota Sienna

3 Answers

i also have a toyta seiana 2005 that makes a noise


The door check on the front of the door tears internally and requires rewelding. This repair has had the warranty extended if I recall c

Models:
'04 - '06 Sienna March 23, 2007
TSB REVISION NOTICE :
^ November 28, 2007: The note below the Warranty Information table has been updated. ^ July 6, 2007: The Warranty Information table has been updated with separate "Combo A" Op Codes. ^ May 29, 2007: The Warranty Information has been updated. The note before step 1 of the Repair Procedure has been updated. Previous versions of this TSB should be discarded.
Introduction
Some customers may experience a popping noise when opening and/or closing the front doors on their vehicle. Use the following procedure to diagnose and correct the condition.

Warranty application is limited to correction of a problem based upon a customer's specific complaint. Repair Procedure
NOTE :Inspect the door frame around the door check mounting area. ^ If a spot weld or check mount area is cracked or split, the following repair method CANNOT be performed and the door assembly MUST be replaced. ^ If a door is to be replaced, all hemming flanges and body panel seams MUST be sealed with body seam sealer prior to painting the door assembly. Refer to the Technical Information System (TIS), CRIB (Collision Repair Information Bulletin), "Bulletin # 16:1987 All: Sealing of Hemming Flanges And Body And Panel Seams," and "Bulletin # 44:1991 All: Body Seam And Joint Sealer Application ". (Note that the CRIBs are located within the CR tab of the main TIS screen.) ^ If a spot weld has separated, have a body shop perform the following procedure.

9bb8415.gif

Sep 14, 2009 | 2006 Toyota Sienna

Not finding what you are looking for?

1,854 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Loading...