Tip & How-To about Dodge Dakota

Blower Motor Problems Most Late Model Chryslers.

Chrysler, Dodge and Possibly JEEP Late Models.(I am not sure about Jeep)

The blower motor resistor is located inside the HVAC duct, (heating, ventalation, and cooling) on the passenger side footwell area. It is accessed from inside the passenger compartment.You can test it with a multimeter to see if it is open. it looks like this when removed.They are about 33.00 from rockauto.com. When you find the connector on the duct that is connected to this resistor block, remove the connector with a small screwdriver, you have to find the lock tab and gently lift it up and pull on the connector to remove the connector. remove one screw and it will come out. most times you can tell if they are bad by looking at them. if you cant test it have someone you know that can do it. I am 99% positive that that is your problem, Unless the connector came loose. Please let us know if this was helpful as i strive to improve helping others on a daily basis.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

blower motor only works on high for 2004 jeep grand cherokee what is the fix ?


This is caused by a defective blower motor speed control resistor. The resistor is located next to the blower motor with one end going into the air ducting and the other sticks out with an electrical connector on it.

Jun 10, 2012 | 2004 Jeep Grand Cherokee

1 Answer

heating system doesnt work


First make sure the fuse and relay for the fan motor are good.If they are then with the ignition and the heater fan switch turned on wiggle on the connection going to the blower motor resistor also check connector for burn marks or melting.The location of the resistor is on the passenger side down towards the floor in the heat duct usally there is to screws that hold it in place.It should be the only thing that has wires on it coming out of the heat duct.

Jan 14, 2012 | 2006 Jeep Grand Cherokee

1 Answer

how do i replace the blower sensor in a dodge 1992 dakota? where is it located? what does it look like?


Chrysler, Dodge and Possibly JEEP Late Models.(I am not sure about Jeep)

The blower motor resistor is located inside the HVAC duct, (heating, ventalation, and cooling) on the passenger side footwell area. It is accessed from inside the passenger compartment.You can test it with a multimeter to see if it is open. it looks like this when removed.b8c93c9.jpgThey are about 33.00 from rockauto.com. When you find the connector on the duct that is connected to this resistor block, remove the connector with a small screwdriver, you have to find the lock tab and gently lift it up and pull on the connector to remove the connector. remove one screw and it will come out. most times you can tell if they are bad by looking at them. if you cant test it have someone you know that can do it. I am 99% positive that that is your problem, Unless the connector came loose. Please let us know if this was helpful as i strive to improve helping others on a daily basis. Yours looks a little bit different than this, but close to it.d63763f.jpg

Feb 04, 2010 | 1992 Dodge Dakota

1 Answer

my blower isn't working


Chrysler, Dodge and Possibly JEEP Late Models.(I am not sure about Jeep)

This is most likely your problem, you can check the fuse, Id855fa1.jpg
am not sure which one it is right now, but if you remove this(it is easy to get to) you can check for power at the connector with a meter, that will tell you if the fuse is good.

The blower motor resistor is located inside the HVAC duct, (heating, ventilation, and cooling) on the passenger side footwell area. It is accessed from inside the passenger compartment.You can test it with a multimeter to see if it is open. it looks like this when removed.b8c93c9.jpgThey are about 33.00 from rockauto.com. When you find the connector on the duct that is connected to this resistor block, remove the connector with a small screwdriver, you have to find the lock tab and gently lift it up and pull on the connector to remove the connector. remove one screw and it will come out. most times you can tell if they are bad by looking at them. if you cant test it have someone you know that can do it. I am 99% positive that that is your problem, Unless the connector came loose. Please let us know if this was helpful as i strive to improve helping others on a daily basis.

Jan 05, 2010 | 1992 Dodge Dakota

1 Answer

Air/fan/heat only works on high in 2005 Jeep Grand Cherokee, or it will start again if I open and slam shut my glove compartment.


Check the blower motor speed dropping resistor pack and it's connections. It is located in the ducting airflow of the blower motor.

Jul 17, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?

2,914 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Loading...