Tip & How-To about BMW 325

Reset oil maintenance light on a 04 bmw 325i

-press and hold the left instrument cluster button
-at the same time turn the key from the off position to the first position (just until the radio lights up, if the check engine light comes on you have gone too far and need to try again)
-after a couple of seconds the display around the odometer should change and say insp or os reset at that point let go of the button and press and hold the button again
-when the word in the odometer area starts to flash let go of the button and just press it like you would if you were resetting the odometer
-at this point it should say end turn the key off and back on again to see if you were successful (it may take a few tries before you get it)

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

HOW TO RESET SERVICE LIGHT ON A 2010 MERCEDES E CLASS AFTER OIL CHANGE


Turn the key to the on position.All dash light's should be on.Push the 0 button on the side of the instrument cluster two times.Turn the key to the off position.Hold the 0 button on the instrument cluster and turn the key to the on position.Keep holding the 0 button until it reset's.

Dec 17, 2016 | Mercedes-Benz E-Class Cars & Trucks

1 Answer

How do I rest the Service indicator for a 2005 CLK Cabriolet? None of the suggestions listed below worked for me.


First make sure all of the doors, hood, trunk, etc are closed.
Turn the key to position 1
Press system select button(lower left buttons on the steering wheel) that looks like sheets of paper until you see mileage reading or temperature displayed.

Press the brightness button on the lower left instrument cluster 3 times. You should hear a signal and see voltage on the display.

Turn the key to position 2

Press the lower scroll forward/back button(steering left arrows)). You should see "service indicator" on the screen

Press the Brightness button again once. You should see oil type on the screen.

Select the oil grade you used by pressing the + & - buttons on the upper right on the steering wheel.

Press the scroll forward/backward button to confirm. Confirm oil reset, press R(brightness button on lower left on cluster) for 3 seconds should appear on the display.

Service confirmed should appear on the display.

Press the upper forward/backward button & "service indicator" appears on the display.

Press the upper system select button(lower left steering wheel button on left) The display should go back to basic mileage or temperature.

If all else fails. I believe the shortcut I took as a tech was, turn the key to the first position, scroll until you see the temperature or mileage displayed. Turn the key off, push in the brightness button and HOLD it while turning the key to the 2nd position. You should see something like do you want to reset service? press R(brightness) button for 3 seconds and it should reset.

Good luck. The newer cars are worse.

Oct 10, 2013 | Mercedes-Benz CLK Cars & Trucks

1 Answer

hi i have a 2004 C200 kompressor aventgarde... it has the muti func steering wheel. each time i turn on the ignition a message on the screen is saying you are x amount of miles over your next service . i will service this car myself,, and then will need to reset this meassage [or get rid of it totally ] what do i need to do please?


Hi, It can be done in several ways. You can try either:
1) Turn key to position 2.
2) Press/release the R button to show the next service due light. Release button.
3) Turn key to Off.
4) Press and HOLD the same R button to view the service light, THEN, within 2 seconds, turn key to position 2.
5) Wait up to 10 second and the light will reset to show new service .


or 1. Insert the key and switch the ignition to position "I".2. Press the display button on the multifunction steering wheel until the "D Service" notification is displayed.
3. Press and hold the reset button located to the left of the instrument cluster until the "D Service" message resets.

Or have it reset by technician when your computer module is checked.

Dec 22, 2010 | 2003 Mercedes-Benz C-Class

1 Answer

TO reset service interval-BMW320d


1. With the key out of the ignition... press and hold the left odometer button.

2. Turn the key to position 1... Meaning radio turns on, but instrument cluster warning lights stay off.

3. Keep holding the button for a few seconds (5-10) untill the display changes and says any of these words... OIL SERVICE or INSPECTION with RESET or RE.

4. Release the button but then again press it and hold (about 5-10 seconds) untill RESET or RE flashes.

5. While the display flashes press the button one more time briefly, and if done correctly the words "end SIA" will show up in a few seconds.

Dec 18, 2009 | 2005 BMW 3 Series

1 Answer

how do you reset the computer after oil change


Resetting the Oil Service or Service Interval Message.
Ignition key must be "off".
• Press and hold the trip odometer button in the instrument cluster (left button), and turn the ignition key to the first position (KLR).
• Keep the button pressed for approximately 5 seconds until one of the following words appear in the display: "OIL SERVICE, or "INSPECTION", with "reset".
• Release the reset button and press and hold it again until "reset" begins to flash.
• While the display is flashing, press the left button briefly to reset the service interval.
After the display has shown the new interval, the following will appear: "END SIA".

Dec 11, 2009 | 2006 Land Rover LR3

Not finding what you are looking for?

1,388 people viewed this tip

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Loading...