Tip & How-To about Cars & Trucks

Mack Fault Codes List

1-1 Engine Oil Pressure Sensor
1-2 Barometric Pressure Sensor
1-3 Fuel Temperature Sensor
1-4 Ambient Air Temp Sensor
1-6 Starter Input
1-7 Engine Coolant Level
1-8 (ASET CEGR) Estimated % Fan Speed
1-10 Aux. Cooling Relay Output
2-1 Engine Coolant Temp Sensor
2-2 (ASET IEGR) Boost Air Pressure Sensor
2-2 (ASET CEGR) Boost Air Pressure
2-3 Intake Air Temp Sensor
2-4 Trans Oil Temp Sensor
2-5 Front Drive Axle Oil Temp Sensor
2-6 Rear Drive Axle Oil Temp Sensor
2-7 Engine Oil Temp Sensor
2-8 (ASET CEGR) Combustion Air Temperature
2-9 (ASET CEGR) Combustion Air Temp Sensor
3-1 Exhaust Temperature Sensor
3-2 Engine Speed Sensor
3-3 Redundant Engine Speed
3-4 Engine Position Sensor
3-5 Engine Brake Output #1
3-6 Engine Brake Output #2
3-8 Trans Splitter Position
3-10 (ASET CEGR) Engine Brake Output #3
4-1 Vehicle Speed Sensor (VSS)
4-2 Fan Clutch Output
4-3 Auxiliary Output #1
4-4 Auxiliary Output #2
4-5 (ASET IEGR) Wastegate Output
4-5 (ASET CEGR) VTG Position Sensor
4-6 Tachometer Output
4-7 Speedometer Output
4-8 Customer Defined Statement
4-9 (ASET CEGR) EGR Valve Mechanism
5-1 Throttle Position Sensor
5-2 Throttle Position Sensor Reference Voltage
5-3 Engine Shutdown Lamp/Alarm
5-5 Electronic Malfunction Lamp
5-6 Spare Relay #3
5-7 Engine Oil Level
5-8 (ASET CEGR) EGR Temperature
5-9 (ASET CEGR) EGR Mass Flow
6-1 Fuel Level
6-2 (ASET CEGR) Turbocharger Speed
6-3 J1708/J1587 Link
6-4 J1939 Link
6-5 All Communication Lost - Engine Shutdown
6-6 Fuel Control Module
6-7 Power Relay
6-8 J1939 Link
6-9 Other ECU Affecting Operation
7-1 Service Brake Switch
7-2 Parking Brake Switch
7-3 Speed Control SET Switch
7-4 Speed Control RESUME Switch
7-5 Battery / Alternator Voltage
7-6 Switched Voltage
7-7 Exhaust Temp Reference
7-9 VTG Actuator
8-1 Electronic Unit Pump #1
8-2 Electronic Unit Pump #2
8-3 Electronic Unit Pump #3
8-4 Electronic Unit Pump #4
8-5 Electronic Unit Pump #5
8-6 Electronic Unit Pump #6
8-9 Solenoid Boost Voltage
9-1 Transport Protocol
9-2 Power Reset Without Key Switch
9-3 (ASET CEGR) Aftercooler Outlet Temperature
9-5 (ASET CEGR) Compressor Discharge Temp
9-8 (ASET CEGR) Auxiliary Output Device #1
9-9 (ASET CEGR) Auxiliary Output Device #2
9-10 (ASET CEGR) Auxiliary Output Device #3
10-1 (ASET CEGR) Internal Sensor Voltage
10-2 (ASET CEGR) 5 Bolt Supply
10-3 (ASET CEGR) Sensor Supply Voltage #1
10-4 (ASET CEGR) Sensor Supply Voltage #2
10-5 (ASET CEGR) Fuel Filter Differential Pressure
10-6 (ASET CEGR) Fuel Delivery Pressure
10-7 (ASET CEGR) Odometer Save Area Failure
10-8 (ASET CEGR) GPS Position Data Not Received
10-9 (ASET CEGR) Watchdog Timer Reset


Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

3 Answers

what is fault code P0069 in car thanks

Trouble Code:
P0069 - (ASE)
Fuel & Air metering, Auxiliary emission controls

DTC Description: Manifold Absolute Pressure (MAP) Barometric Pressure (BARO) Correlation

P0069 Description Manifold Absolute Pressure (MAP)/Barometric Pressure (BARO) Correlation is the generic definition for the P0069; however your vehicle's manufacturer may have a different definition and information for the P0069 code.

Read more: http://www.engine-codes.com/p0069.html#ixzz47thnToR7
P0069 Manifold Absolute Pressure Barometric Pressure Correlation

May 06, 2016 | 2007 Nissan Navara 2.5

1 Answer

How do I fix code 13 engine speed sensor Above 1000 rpm

Clearing the codes is simple that is done by removing the fuse of the EFI from junction box 2 for 10 seconds. Make sure to remove the jumper wire and switch the key off before clearing the codes.

Here are some common Lexus vehicles 1990-1995 codes:

Code 12 and Code 13 Rpm signal circuit fault
Code 14 Igniter signal circuit fault
Code 16 ECT control signal fault
Code 21 and Code 28 Main oxygen sensor fault (for ES300; SC300 & GS300 models)
Code 22 Coolant temperature circuit fault
Code 24 Intake temperature sensor circuit fault
Code 25 and Code 26 Air fuel ratio fault (for ES300 & SC300 models)
Code 27 Sub-oxygen sensor circuit fault (for ES300 CA & GS300 models)
Code 31 Low airflow meter voltage (for ES300 and GS300 models)
Code 32 High airflow meter voltage (for ES300 model)
Code 35 Barometric pressure sensor circuit fault (for GS300 & SC300 models)
Code 41 and Code 47 Throttle position sensor circuit fault
Code 42 Vehicle speed sensor circuit fault
Code 43 Starter signal
Code 51 Switch condition signal fault (for ES300; GS300 & SC300 models)
Code 52 Code 52 and Code 55 Knock sensor circuit fault
Code 71 EGR system circuit fault (for ES300; GS300 & SC300 models)
Code 78 Fuel pump control circuit fault (for GS300 & SC300 models)

Nov 18, 2014 | 1990 Lexus LS 400

1 Answer

What do these diagnostic codes(PO106,PO121) mean for a 2000 deawoo lanos.

OBD II Fault Code
  • OBD II P0106
Fault Code Definition
The Manifold Absolute Pressure Sensor/Barometric Pressure Sensor measures the rise and fall of the air pressure inside the Intake Manifold. This provides critical data needed for the Power Train Control Module (PCM) to control the Air Fuel Ratio, the Ignition Spark Timing, and many components of the Emissions Control Systems. The Manifold Absolute Pressure/Barometric Pressure Sensor P0106 code is set when there is a problematic or erratic performance in the voltage signal to the PCM.
  • Check Engine Light will illuminate
  • In many cases, no abnormal symptoms may be noticed
  • In some cases, the engine may be hard starting and/or get poor fuel economy
  • In some cases, noticeably poor engine performance may occur
Common Problems That Trigger the P0106 Code
  • Manifold Absolute Pressure Sensor/Barometric Pressure Sensor is defective
  • Intake Manifold vacuum leaks
  • Faulty or corroded Manifold Absolute Pressure Sensor/Barometric Pressure wiring or connections
Common Misdiagnoses
  • Manifold Absolute Pressure Sensor/Barometric Pressure Sensor is replaced when the real cause is an Intake Manifold vacuum leak
  • Manifold Absolute Pressure Sensor/Barometric Pressure Sensor is replaced when the real cause is a stuck-open EGR Valve
  • Manifold Absolute Pressure Sensor/Barometric Pressure Sensor is replaced when the real problem is a defective Idle Air Control Motor, which causes a very low engine idle

Oct 28, 2010 | 2000 Daewoo Lanos

2 Answers

i have a gmc envoy & the trouble codes are p0107,p0130,p0135 & p0171 can you tell me what the problem can be.

P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)

P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)

P0171 System too Lean (Bank 1)

Check your Manifold Absolute Pressure Sensor, and it might be a good time to install a new Upstream O2 Sensor.

It might also be beneficial to have your fuel pressure checked if the engine is really running Lean, but this may be caused by a faulty O2 sensor.

Jul 19, 2010 | GMC Envoy XL Cars & Trucks

Not finding what you are looking for?

391 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions