Tip & How-To about Cars & Trucks

?JCB FAULT CODES LIST

P0087 (flashing code 227) shared sump low pressure fault (for pump without pressure supply)
The main fault symptoms
• Engine severe vibration.
• idling unstable
• Output Fall
• exhaust smoke
• It may be too large output
P0088 (flashing code 118) shared the tank pressure is abnormally high (first or second stage)
The main fault symptoms
• Engine severe vibration
• idle instability
• Output Fall
• channeling gas engine failure
• exhaust smoke
• It may be too large output
P0089 (flashing code 151) shared the tank pressure failure (for pump pressure supply is too large)
The main fault symptoms
• Engine severe vibration
• idle instability
• Output Fall
• channeling gas engine failure
• exhaust smoke
• It may be too large output
P0090 (flashing code 247) SCV drive system open, + B short circuit or shorted to ground
The main fault symptoms
• Depending on the open / short situations, there may be an engine stall and / or launch
Machine channeling gas.
• exhaust smoke
• Output is too large
P0107 (flashing code 71) atmospheric pressure sensor circuit input low (open or shorted to ground)
The main fault symptoms
Due to spare the equivalent altitude 2000 m (6562 ft)
• exhaust smoke at high altitude.
• insufficient output at low altitude
P0108 (flashing code 71) atmospheric pressure sensor circuit input high (+ 5V shorted)
The main fault symptoms
Due to spare the equivalent altitude 2000 m (6562 ft)
• The high altitude exhaust smoke
• lack of low altitude output
P0112 (flashing code 22) intake air temperature sensor fault (low voltage fault, earth fault, short circuit)
The main fault symptoms
• When cold starting, may exhaust white smoke.

More here http://truckmanual.weebly.com/jcb-fault-codes.html

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

What parts do you recommend for a fault on my Hyundai Tucson which has developed faults?


uh oh, 1186 and 0087 are both related... fuel pump or the filter or both! either case the filter is now located inside the fuel tank

P1186 Hyundai Fuel Pressure Too Low


P0087 Fuel Rail System Pressure Too Low

"Potential causes of a P0087 trouble code may include: Weak fuel pump, clogged filter or screen, restricted fuel supply line Faulty fuel pump driver module Faulty fuel pressure sensor"


How to Change the Fuel Filter on Hyundai Tucson eHow

according to eHow, you can access the filter relatively easily. (although the pic is an illustration of something not really related to this ~ why they showing a fuel petcock that's not even on your car?)

P2112 Throttle Actuator Control System Stuck Closed

"Possible causes:
- Throttle Body Plate Binding
- Faulty Throttle Actuator
- Throttle Actuator harness is open or shorted
- Throttle Actuator circuit poor electrical connection"

older models we had the gas pedal attached to a cable to move the butterfly valve on the throttle body. Now it's this newer drive-by-wire stuff... remove air intake hose and check / clean / move the throttle body valve by hand first to see if it's binding or not

then, go from there on testing the actuator and tps

Apr 17, 2015 | 2006 Hyundai Tucson

1 Answer

P0313,p008A,p0087 . I don't understand this codes from my Lr4 2010


code p0313 refers to misfire detected---low fuel level===causes-- fuel system ---mechanical fault ( check fuel pressure, fuel filters and fuel pump)
code p0087 refers to fuel rail /system pressure --too low=== causes --fuel pump,--fuel pressure regulator--fuel supply line blockage--mechanical fault. ( have the fuel system pressure tested.)
The code you have listed as p008A is not in the book and you have not given an make or engine model to refer to in other places. I will refer to the code as p0084 which refers to exhaust valve control solenoid, bank 2--circuit malfunction===causes --wiring--exhaust valve control solenoid---ECM ( this will present as a rough running engine or problem starting/ shutting down

Oct 30, 2014 | Cars & Trucks

1 Answer

08 Chevy Kodiak c4500 duramax desiel i replaced the MAF sensor because the code reader said P0102 now it says P0087 that is the problem but everytime I'm hauling something the engine always decreases its speed when going uphill then the engine light come on so I reset the system good until the hills and back to square 1 what do you think I should do to fix it and what parts should need


DTC P0087: Fuel Rail Pressure (FRP) Too Low

Circuit/System Description
The fuel injection pump supplies high pressure fuel to the fuel injection rails, and then to the fuel injectors through high pressure pipes. The fuel rail pressure (FRP) sensor is a three wire sensor mounted in the right fuel injection rail. The FRP sensor uses a 5-volt reference circuit , a signal circuit, and a low reference circuit to monitor fuel rail pressure. This information is sent to the engine control module (ECM) to assist in the fueling of the engine.

Fuel Pressure Regulator Solenoid Supply Voltage
P0088, P0090
P0088
P0090
P0087, P0191, P2510
Conditions for Setting the DTC
P0087
• The actual FRP is more than 15 MPa (2,176 psi) below the desired FRP.
OR
• The actual FRP is less than 22.5 MPa (3,263 psi).

Action Taken When the DTC Sets
• DTCs P0087 and P0088 are Type A DTCs.
• The ECM commands the engine to operate in the Reduced Engine Power mode.
• The message center displays Reduced Engine Power.

Important: Because of the cleansing properties of the biodiesel, switching from the straight diesel to a biodiesel blend can prematurely restrict the fuel filter with normal deposits in the fuel system. A fuel filter replacement might be required sooner than the recommended interval.
P0087
If DTC P0090, P0168 or P0191 is also set, refer to Diagnostic Trouble Code (DTC) List - Vehicle.
Ignition ON for 90 seconds, verify the scan tool FRP Regulator Command parameter is less than 20 percent.
? If greater than the specified range, replace the ECM.
Attempt to start the engine.
? If the engine does not start, refer to Engine Cranks But Does Not Run.
Install the CH-48027 to the fuel rail service port and slowly increase the engine speed until reaching wide open throttle (WOT). The value should be between 1-4 inches Hg vacuum.
? If more than the specified value, inspect for restricted fuel filter or damaged supply lines.
? If no restriction was found, test for high fuel return flow. Refer to Fuel System Diagnosis - High Pressure Side.
With the engine idling or at an idle, command the fuel pressure control to 180 MPa (26,106 psi) with a scan tool. Observe the Actual Fuel Rail Pressure parameter. The actual fuel pressure should be the same as the commanded pressure.
? If the Actual Fuel Rail Pressure is less than 165 MPa (23,931 psi), refer to Fuel System Diagnosis - High Pressure Side.
Important: If the fuel temperature is near 121°C (250°F) during the duplication of the complaint, or in the Failure Records for this DTC, inspect for a restriction in the fuel cooler air flow or the fuel heater always ON. Refer to Fuel Heater Always On.
Operate the vehicle within the conditions for which the customer complaint occurs while observing the CH-48027 . You may also operate the vehicle within the conditions that you observed in the Freeze Frame/Failure Records.
? If the vacuum was more than 12 inches Hg of vacuum at any time in the operating range, inspect for kinked or restricted fuel supply lines.
Operate the vehicle within the conditions for which the customer complaint occurred. Observe the Actual fuel Rail Pressure and Desired Fuel rail Pressure parameters with a scan tool. Fuel pressures should be the same for both parameters.
? If the Actual Fuel Rail Pressure is less than the Desired Fuel Rail Pressure, refer to Fuel System Diagnosis - High Pressure Side.
? If fuel system tests normal, refer to Diagnostic Aids.

Aug 20, 2017 | Cars & Trucks

2 Answers

chevy duramax code p0087


P0087 GMC - Fuel Rail Pressure Malfunction Pressure Too Low

Possible causes - Faulty fuel pump
- Blocked fuel filter
- Faulty fuel pressure sensor
- Fuel pressure sensor harness is open or shorted
- Fuel pressure sensor electrical circuit poor connection
- Faulty Fuel injector

Apr 09, 2014 | 2006 GMC Sierra 3500

1 Answer

my car starts hesitates the engine vibrates oil light comes on then sputters and cuts off


run the fault codes . Check for idle speed sensor and MAF sensor. It should be idling around 900rpm and the oil light coming on ( assuming you have enough oil in the sump) will be because of the very low idle rpm not pumping enough oil to maintain pressure.

Jul 21, 2013 | 2000 Pontiac Grand Am GT

Not finding what you are looking for?

579 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Loading...