Tip & How-To about Ford Edge

2008 Transmission Torque mount review

A short review of the new transmission torque mount for a 2008 Ford Edge
2007 thru 2008 Ford Edge Anchor Industries Transmission Torque Mount review

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

3 Answers

how to remove and replace auto transmission ?


Its a big job gave you and example for neon

Jan 18, 2015 | 2001 Chrysler Voyager

1 Answer

how to install a clutch kit on my 1994 mitsubishi mighty max


Disconnect the battery, disconnect the Hydraulic Line from the Slave Cylinder, Remove the Starter (2 bolts, 2 wires. Bolts are 14mm, 1 wire is 12mm, 1 plugs in), Remove the Driveshaft(s) (4 12mm bolts) Remove the 6 bolts from the bellhousing (4 are 14mm, 2 are 10mm)
Remove the bolt from the Transfer Case Mount, 12mm (only if it's a 4WD, if it's 2WD this doesn't apply), remove the 2 bolts that hold the Transmission Mount to the Crossmember (12mm or 14mm, it varies)
Slide the transmission back on the crossmember, away from the engine, I recommend running a ratchet strap across the frame to balance the transmission.
Remove the Pressure Plate from the Flywheel (Six 10mm bolts), Inspect the Pilot Bearing (if it needs replaced, you'll need to remove the Flywheel which is held on with six 18mm bolts, drive out the old bearing and drive in the new one, reinstall the flywheel, using Threadlocker on the bolts, torque the bolts to 100 ft lbs) Install the new clutch disc and Pressure Plate, with the centering tool inserted through the disc into the pilot bearing. Use thread locker on the pressure plate bolts and torque them to 20 ft lbs. Remove the centering/alignment tool after you've bolted it together
Remove old Throw Out bearing from input shaft on the transmission and slide the new one on. Slide the Transmission forward (make sure the input shaft slides into the pilot bearing, don't force the transmission into place or you could damage the clutch disc or break the input shaft) Torque the Bellhousing Bolts to 40 ft lbs (4 14mm bolts), Torque the 2 10mm bolts to 14 ft lbs, Install the Starter (torque bolts to 23 ft lbs), Reconnect Hydraulic Line to Slave Cylinder. Torque Transmission Mount Bolts to 30 ft lbs.
Reinstall Driveshafts, torque bolts on flange/yoke to 40 ft lbs. Fill Clutch Master Cylinder with DOT-3 Brake & Clutch Fluid, Open Bleeder Screw on Slave Cylinder and bleed the air out of the system, close bleeder screw.
Reconnect the wires to the Starter, Reconnect the battery.

Aug 24, 2011 | Mitsubishi Mighty Max Cars & Trucks

3 Answers

My Ford Focus 2006 4 cyc has an engine code PO741 on my OB2. What does that mean?


P0741 Torque convertor clutch circuit failure,it is located in the transmission valvle body, it is attatch to the valve body you can remove it seperately as long as your going to own the Ford focus you might as well get use to replacing these all the time,very common transmission issue with todays car. By the way it is sensitive to worn transmission fluid,when you dont service often these are suspectable to failure.

Apr 22, 2011 | Ford Focus Cars & Trucks

1 Answer

where is the starter located on my 2003 nissan sentra ser


Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  3. Lightly lower the transmission to make room and pull out the dipstick tube.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  5. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
    • Negative battery cable
  6. Remove the transmission jack
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 70 inch lbs. (8 Nm)
    • Starter electrical connections
    • Negaative battery cable
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle

      Image 89612G12l Not Found

    To install:
  2. Install or connect the following:
    • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
Altima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Starter
    To install:
  2. Install or connect the following:
    • Starter and torque the bolts to 60 inch lbs. (7 Nm)
    • Starter electrical connectors
    • Harness bracket
    • Air inlet tube
    • Negative battery cable

Nov 03, 2010 | 2003 Nissan Sentra

Not finding what you are looking for?

832 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Loading...