20 Most Recent 2006 Toyota Tacoma Questions & Answers


Try tightening the bolts that connect it on the motor...if this doesn't work it's probably a gasket ...simple fix if nothing is cracked is to use a cereal box or such and after removing the connection to trace a home made gasket and if you can get some silicone put it on both sides wait maybe 5 minutes then reinstall....if it's just the hose that's leaking...use one of the screw ethos hose clamps and tighten it...hope this helps

2006 Toyota... | Answered on Sep 27, 2016


Go under the dash and disconnect the brake light switch then unscrew the plastic nut that retains it to the pedal bracket. See picture below, the nut is brown in the picture of the switch.


26232651-q1tuxh11to3jkajalh5x1kxq-2-0.jpg

2006 Toyota... | Answered on Jul 07, 2016


Best Manuals


for better result of your problem visit this site

2006 Toyota... | Answered on Apr 19, 2016


You can use pipe strap, inexpensive from Lowes/Home Depot. You can use this to replace old rusted out tank straps. You may need to drill and re-***** the strap into a solid area near the old locations.

2006 Toyota... | Answered on Apr 18, 2016


Could be a bad amp or amp fuse. No amp. Replace the radio, unless you are a computer tech. Then tear it apart and find the problem. Could be bad solder joints. The most likely cause. Usually at the face of the radio.

2006 Toyota... | Answered on Jan 01, 2016


2TR-FE 2.7 is 1-3-4-2
1GR-FE 4.0 is 1-2-3-4-5-6
Cylinder #1 is front on the 2.7, front passenger side on 4.0.
On the 4.0, passenger side bank is 1-3-5, driver side is 2-4-6 (front to back).

2006 Toyota... | Answered on Nov 30, 2015


Try removing bulbs then remove the connection on the headlight switch if it doesn't burn there your problem

2006 Toyota... | Answered on Sep 11, 2015


wows thats not v,gud. all you need to do is lose alln the screws that are used to tight the ignition plastics,,,nd u will need an alien key rto lose the main ignition on the steering wheel... i dont think you can do that on ur own if u aint an experienced engineer....i wil advice u to call an experienced engineer to bail u out....

2006 Toyota... | Answered on Jul 10, 2015


PCM and ECU is the same part

2006 Toyota... | Answered on May 24, 2015


Needs a cat and need to check the injector and coil. Coil most common on that model

2006 Toyota... | Answered on May 23, 2015


Intake Air Temperature (IAT) sensor and Manifold Absolute Pressure (MAP) sensor are combined into a single assembly which is called Mass Air Flow (MAF) sensor. This MAF sensor is located on the air filter box near air filter hose, and is connected with a five wire connector. You cannot replace the IAT sensor alone. Instead a MAF sensor is replaced altogether.

25646166-ts5vql1j3jwqenesgxdwpnsg-5-0.png



25646166-ts5vql1j3jwqenesgxdwpnsg-5-2.png
Thank you for visiting Fixya.

2006 Toyota... | Answered on Apr 27, 2015


This is the 2001-2012 Toyota Tacoma wiring diagram, Toyota Tacoma IAT (Intake Air Temperature) Sensor Location and the Toyota Tacoma MAF (Mass Air Flow) Sensor Location, also included is a pinout of the sensor. You are likely installing a performance chip or a cold air intake kit for increased HP (Horsepower). You will want to be sure to disconnect the car battery before adding performance products.




Here is the Toyota Tacoma's Iat sensor diagram:




ab0b7213-0c7f-459c-b26e-77a685236e74.jpg

2006 Toyota... | Answered on Apr 14, 2015

Not finding what you are looking for?

619 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

71525 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7029 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Tacoma Toyota

  • Tacoma Toyota

Most Popular Question

get brake light switch out in 2006

  • Cars & Trucks
Loading...