20 Most Recent
2004 Audi A4 Questions & Answers
Try to fine out why the flasher are staying on on a 2004 A4
The flashers are controlled by electrical relays that switch power to them on and off. If the electrical relays malfunction internally, they can cause the hazard lights to act up. Another possibility could be an issue with the turn signal or hazard switches themselves, perhaps internal faults.
9/23/2021 4:57:08 AM •
2004 Audi A4
•
Answered
on Sep 23, 2021
I have an 04 Audi A4 B6 1.8 Turbo I'm looking for the fuel pump relay location
you can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single t hing is covered
within seconds u can get the access and it's totally illustrative complete
3/6/2019 5:23:27 PM •
2004 Audi A4
•
Answered
on Mar 06, 2019
Brake pad replacement 2004 audi a4 and rotor how
YOU NEED REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER.THEN YOU RAISE VECHICLE SAFELY.SUPPORT IT WITH JACK STAND.MAKE SURE VECHICLE IS ON LEVEL SOLID GROUND.REMOVE TIRE OR WHEEL.THEN YOU NEED A LARGE C - CLAMP.PLACE C - CLAMP OVER BRAKE CALIPER AND BRAKE SHOE BACKING.TIGHTEN C - CLAMP JUST ENOUGH PUSH CALIPER PISTON BACK IN CYLINDER BORE TO REMOVE CALIPERS FROM ROTORS.TO REMOVE BRAKE CALIPER YOU NEED 2 OPEN AND BOX END WRENCHES ONE TO HOLD CALIPER SLIDE PINS AND THE OTHER WRENCH FOR LOOSEN CALIPER BOLTS.THEN YOU REMOVE CALIPER AND REPLACE FRONT BRAKE SHOES.IF YOU NEED TO REMOVE BRAKE ROTORS JUST REMOVE THE BRAKE CALIPER CARRIER SUPPORT BOLTS THE REMOVE THE BRAKE CALIPER CARRIER SUPPORT THEN REMOVE ROTOR.YOU NEED TO REPLACE BOLTS WITH NEWS AND USE LOCK TIGHT.THEN YOU PUT IN NEW BRAKE PADS IN CALIPER PUT CALIPER BACK ON SUPPORT CARRIER.REPLACE WITH NEW BOLTS USE LOCK TIGHT THEN TORQUE BOLTS TO 26 FT LBS.MAKE SURE MASTER CYLINDER COVER IN PLACE.WHEN YOU FINISH REPLACING BOTH FRONT BRAKE PADS PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST BRAKE ROTORS SO YOU WILL HAVE FIRM BRAKES WHEN YOU APPLY THEM. THEN CHECK YOUR BRAKE FLUID LEVEL IN MASTER CYLINDER MAKE SURE ITS NOT LOW. MAKE SURE YOU HAVE FIRM BRAKES BEFORE DRIVING.IF YOU HAVE ANY PROBLEMS CHANGING FRONT BRAKE PADS YOU CAN GO TO ANY AUTO PARTS STORE AND BUY A HAYNES REPAIR MANUAL.
3/5/2019 12:14:18 PM •
2004 Audi A4
•
Answered
on Mar 05, 2019
The battery of my audi
Yes. If you can enter through the trunk - open the bonnet, replace or recharge battery. Sorry I don't know that model or where the rear seat release is. But I hope this helps.
Mike
11/8/2018 6:17:13 PM •
2004 Audi A4
•
Answered
on Nov 08, 2018
My 04 audi a4 not firing went out this eav it
Usually the clicking noise is the starter solenoid not getting enough amps because the battery is shot.
Suggest jump start vehicle then drive it to Autozone. They will test it for free and even install the new battery for free.
They have one of the best battery warranties in the business. Be sure to keep your receipt paperwork in the glove box.
2/7/2018 3:45:24 PM •
2004 Audi A4
•
Answered
on Feb 07, 2018
Audi A4 2004 Gear Select flashing
Dealers tend to be crooks. Honestly, as an ex dealer I suggest take it back to where it has be gotten and request it be fixed. Most dealerships are often nice about that
2/5/2018 2:30:24 AM •
2004 Audi A4
•
Answered
on Feb 05, 2018
Not finding what you are looking for?