I started my car this morning and I noticed the check engine light was on...no big deal well then I put my foot on the brakes to put the car in nutreul to leave but the shift wouldnt move. It acted like it was stuck. I turned it off and then back on and the same thing. I checked the transmission fluid, and it was fine. Whats wrong and what can I do to fix it??? Please help.
sounds like your brake/shift interlock solenoid is not releasing.
Your owner manual will tell you how to bypass in emergency.
Check your fuse first. fuse panel on instrument panel.
Please rate as fixed if this helps.
Fuse 23 - 1 5 amp
Fuse 34 - 7 1/2 amp
check enigne light not related.
----------------------------------------------------
The selector lever lock can be moved mechanically out of position ”P" when for example the battery is disconnected or completely discharged.
Using a ball point pen or similar item as an unlocking lever, push forward and hold in position.
Move the selector lever out of position "P".
NOTE: If the selector lever is moved back to ”P" it is re-locked.
Selector Lever Lock
Posted on Apr 28, 2009
P1451 Code on Mercury Cougar. How do I fix it
Here is the information that you need:
NOTE
Enter this Pinpoint Test only when directed here.
The use of a soap solution, such as SNOOP, around the fuel filler cap or the use of the hydrocarbon emission analyzer to determine an evaporative emission system leak is not recommended. The mandatory Rotunda Evaporative Emission System Leak Tester for OBD II (including the ultra-sonic tester) is the only device to be used at this time for evaporative emission system leak detection.
This Pinpoint Test is intended to diagnose the following:
Evaporative Emission (EVAP) Monitor System
Posted on Sep 26, 2009
i have a 2000 cougar v6 my lights started flickering and i replaced the alternator it was good then 3 months later my battery went and i changed it and the flickering is worse my kights flicker my dash flickers my blower motor for the heat goes up and down my rpms also help
In some 1999/2000 Cougars the wire between the battery and the voltage regulator(altenator) had a resistance reading that is too high. Ford has issued an TSB 00-25-6 that has instructions on how to replace this wire. The part # for the replacement wire is
1S8Z-14A411-AA. I'm in Michigan and a local dealer found one for me in South Bend,IN
Posted on Jul 29, 2009
My 2000 mercury cougar will not start! It is not the starter or battery or fuel pump! What could it be?
what is anti-theft light doing? It should come on solid for about 2 sec after you turn the key on then turn off. If it is flashing after this then it is not seeing the computer chip in the key and you have a PATS problem.
Posted on Jan 30, 2009
Hi,
My 2000 Mercury Cougar has been showing the CEL for a while now. The
guys at Autozone said the code was P0401 - Insufficient EGR
circulation. I took the car in for an estimate and the mechanic told me
the DPFE/EGR pressure sensor was faulty and needed to be replaced.
Since I wanted to learn more about fixing my car myself, I looked the
DIY for DPFE replacement online. I switched my DPFE sensor (part#
F7ue-9j460-AA) with BWD EGR155 from Advance auto parts. However, 10
miles after resetting the codes (by disconnecting battery), the CEL was
on again. What could be the problem? Should I replace the EGR valve or
solenoid? What diagnosis can I do to figure out whats faulty? The only
other symptom is slightly lower gas mileage, but since I drive in
Boston traffic I cant say for sure if the EGR is causing that.
I would really appreciate your help.
Thanks!
Posted on Jul 20, 2009
My Power door locks do not work on either door in my 2000 Mercury Cougar that I just bought yesterday. I have to manually lock or unlock the doors with the key from the outside every time. I am assuming it is a fuse but can not find the fuse location from the diagram. Please help somebody. Thank you so much.... Elena
Power door locks are on the same fuse as the alarm system. The fuse is located in the passenger compartment fuse panel under the steering wheel. There is a pull down lever that will release the fuse box. The fuse for the alarm system/locking system is #25. Yellow color and a 20 ampere rating.
Posted on Oct 09, 2009
How to replace fuel pump on 2000 Mercury Cougar.
First off I am sorry you have a cougar also.... I am on my third fuel pump ... stupid car anyways. If you didn't do it yet one make sure you get one from the dealer... Hopefully you will have better luck than me i paid 400 last year and tried to get one on warrenty then I had to wait since may to august to get it good news for you Ford should have it off back order. It is in the fuel pump you can 1. drop the tank (huge pain) or 2. it is WAY easier to take out your back seat ther eis a small hole to see the pump covered by a black plastic thing. You can then make the hole bigger and pull the pump out that way.
Posted on Aug 20, 2010
It appears my AC compressor clutch has gone out based off of information given to me. I don't not have the money to take it to a shop and have it fixed but i have decided to buy a bypass pulley, was told this was my only solution cause if i bought a short belt ''something'' would turn backwards, instead of replacing the whole AC compressor. Removing the belts is not an issue for me but i honestly do not know how to remove and install the bypass pulley. Was hoping to get a head start on it before the part got here so i can prep my car in my garage. Any and all help is appreciated. And no, as you can probably tell I am not a car guy.
ok well sounds to me like your gonna have to remove the ac comp. itself which will take a little work... the new pully will prolly be a bracket that bolts up were the ac comp is now but it will be free spinning i have not done this specfic one but thats like one i did once you will have to empty the ac system of all refrig which to be done properly you must have a recovery machine {which means shop which means money im sorry} then remove the lines and un bolt comp. when all said and done you will notice better gas milage so thats a plus i hope this was helpfull and once again this is how i did it to my old blazer i used to have so i hope that its the same for you best of luck man
Posted on Mar 27, 2009
Diagram for power steering lines for 2000 cougar
Item
Part Number
Description
1
Fluid reservoir
2
Steering wheel
3
Steering column assembly
4
Flexible coupling
5
Tie-rod end
6
Tie-rod
7
Steering gear boot
8
Steering gear
9
Fluid cooler
10
Steering gear hoses
11
Power steering pump
Posted on Sep 26, 2014
how to replace rear wheel bearings on a 2000 cougar?
Hi,welcome to fixya.
The rear wheel bearings are not adjustable. If the bearings make noise or become loose, they must be replaced.
Removal & Installation
With Drum Brakes
NOTE
The wheel bearings are contained within the wheel hub and must be replaced as an assembly.
NOTE
Do not use an impact gun to remove the hub retainer nut.
Fig. Using suitable tools loosen and . . .
Fig. . . . remove the hub retaining nut dust cover
Fig. Using suitable tools, loosen and . . .
Fig. . . . remove the hub retaining nut
Fig. Carefully slide the hub and bearing assembly off of the spindle
To install:
Road test the vehicle and check for proper operation.
WARNING
Do not use an impact gun to tighten the hub retainer nut, otherwise the bearings may be damaged.
Thank You for using fixya........iluv2fish........Ray........
Posted on Jul 16, 2010
962 questions posted
Usually answered in minutes!
1,305 Questions
345 Questions
361 Questions
333 Questions
245 Questions