Tech Support
Local Repair
Product Recommendations

Home | My Expertise | Sign In

Help me with
Search
Home | Chevrolet | 1988 S-10

Troubleshooting 1988 Chevrolet S-10, Support & Service

Find a Solution

Related Searches: not starting  firing order 10  firing order cyl  low range  location ignition module  choke pro  chevy compression  window wires  mirrors  tools  rear brakes  10 1988 chevy wiring  97 fuel pump s10  guides window  handle off window  10 chevy diagram engine  clutch  distributer 
See All

View unsolved problems

Solved Problems


Click here to get instant support from our best Experts!
Get Expert Assistance

Chevy S-10 Start problems
it will start but only run for a couple of seconds .Injector gets a pulse in start mode when cranking.Put on new fuel filter,ignition...
1 Solution
1989 Chev 2.5 S 10. I replaced the spark plug
1989 Chev 2.5 S 10. I replaced the spark plug wires and have mixed up the wires. What is the order of the wires.
1 Solution
is there supposed to be some kind of spring
is there supposed to be some kind of spring pressure on the throw out bearing arm when the slave cylinder is off? or should it just move...
1 Solution
rough idle when started and slow to gain power
when i start my 89 s10 2.8 4wd after sitting for any extended period of time, it idles rough and sounds like it wants to die. Also, of the...
1 Solution
my 98 s10 will not stay running
my 98 s10 will not stay running , it starts and runs for a few seconds thn dies. i replaced the crank shaft and put motor back in now i am...
2 Solutions
wheel bearings on 1988 chevy S-10
Re place wheel bearings on 1988 chevy S-10
1 Solution
have a 1988 s/10 blazer. came with a 2.8
have a 1988 s/10 blazer. came with a 2.8 ENGINE.Swap it out to a 350. have 5 wires that went to the bottom driver side of the 2.8 motor that...
1 Solution
got fuel to throttle body, but wont spray fuel
got fuel to throttle body, but wont spray fuel
1 Solution
1989 rear brakes for a chevy s-10
1989 rear brakes for a chevy s-10 I can not pull the left side drum off. It is loose but it seems like the pads are still contacting...
1 Solution
the switch doesnt work
the switch in my 1988 2.8 s10 dosnt work .but it works when you hot wire the switch. how do it fix it?
1 Solution
what is the purpose of an egr valve?
what is the purpose of an egr valve?
2 Solutions
what are the symptoms of a bad catalytic
what are the symptoms of a bad catalytic converter? how hard are they to replace and where is mine located on my 1988 chevy s10 2.8 ltr?
1 Solution
1988 chevy s-10 2.8 liter v-6 Idles rough and
1988 chevy s-10 2.8 liter v-6 Idles rough and stalls out if foot is not depressing gas pedal. It affects hydraulic brakes also. Swapped...
1 Solution
blown valve
how do i get the head off?
1 Solution
my 1988 chevy s10 idles but when accelerating has
my 1988 chevy s10 idles but when accelerating has no power. i have replaced the throttle position sensor , the injectors and the map sensor....
2 Solutions
[1] 2 3 4 5 6 7 8 9     Next

Sponsored Links

Ask our Experts

Ask

 

Solve Your Problem Now!
Chat Live with an Expert
Chat Now

Top Car Repair

Nationwide Collision...
(713) 838-2886

collisionrepairadvice....
(602) 909-6450

See More
Get Listed!


Insert Link
Insert Image
Insert You-Tube clip
Insert List
Insert List
Spell Check

What is this?



Select