20 Most Recent
1983 Mazda 626 Questions & Answers
2000 mazda 626 timing belt broke fixed that now it
Have you tried disconnecting the battery and resetting the computer? if so ground your thermostat again with a good connection...I believe the computer reads the thermostat first and secondarily your injector pulse it can be wacked..also fuel..check it..check it now good luck...GOD bless
What is the torque for a 1983 mazda 626 fe sohc engine
go to autozone.com and login or set up an account if you don't already have one it's free. Then you will be able to punch in the year make and model of your car and find repair manuals for any vehicle you desire. In your case 83 mazda 626. and go to cylinder head info and there you will find what your looking for. Good luck.
Sometimes the electronic dash doesn't work
It is in the circuit board itself,or the plug in,in the back of the cluster,removal,and checking it,and tightening the terminals up,by gently bending them to fit tighter might help.
I need 2 no 13b spark plug diagram
All you need to know is how many cylinders early have 4 cyl and firing order is 1342 and No 1 is where water pump is ans any lead HT the correct will do If 6 cylinder then its 153624 firing order and still 1 is the nearest one to the water pump
My 1983 mazda 626 wont turn over, I have changed
It sounds like either the starter or ignition switch is bad. The easiest way to check which is at fault is to look at the dash lights when you go to crank it over. If when you crank it over the dash lights dim slightly, then that tells you that it is probably not your ignition switch. I would then look towards the starter being the problem. Possibly just a wire loose or off. If when you crank it over the dash lights do not dim slightly, then it is probably your ignition switch. Hope this helps.
Where is the water pump
The water pump is located in the timing belt cover you will have to remove the timing belt
to change it .. it would be a great idea to change your timing belt too !!
have a great day hope it wil help you thanx
Denis
Brakes
us a large " C " clamp and place one end on the back side of the caliper and the other end on the piston side ( place the old brake pad over the hollow part of the piston hole ) nd slowly tighten the " C " clamp. you will need to do this slowly as I say or the brake fluid will squirt out of the top of the master cylinder.
Good luck and I hope that this helps you.
Where is the trunk light switch/sensor located in a 1999 mazda 626
I am not sure where the switch is located ... but I had generic trunk lid light issues on an older car. It turned out NOT to be a switch issue ... but a wiring issue. The trunk had been opened enough times over the years that the covered/taped wire bundle that goes from the body to the trunk had flexed too many times and right around the hinge area several wires had broken. The problem was found by doing a number of continuity checks on the wiring after I had frustratingly looked at all switches and light bulbs!!
Check engine light on
Diagnostic Trouble Codes OBD1
Mazda
02
Crank Position Sensor (NE Signal).
03
Cam Position Sensor (SGC Signal).
05
Knock Sensor.
08
Air Flow Sensor.
09
Engine Coolant Temperature Sensor.
10
Intake Air Temp. Sensor (Air Flow Sensor).
12
Throttle Position Sensor.
14
Barometric Absolute Press. Sensor.
15
and/or
23
Heated Oxygen Sensor (Inactivation).
16
EGR Function Sensor.
25
Pressure Regulator Control Solenoid Valve.
26
Purge Control Solenoid Valve.
28
EGR Vacuum Solenoid Valve.
29
EGR Vent Solenoid Valve.
34
Idle Air Control Valve.
41
VRIS 1 Solenoid Valve.
46
VRIS 2 Solenoid Valve.
Car was stalling on standstill
At
www.reliable-store.com has books on every vehicle and also how to service/repair it.
service/repair/owner's/maintenance manual with
parts info, fuse box, gear box, PCV, torque specs,coiling, wiring diagrams, electrical diagrams, fuse diagrams, error codes, etc everything
Worth it
Not finding what you are looking for?
