Top 20 2005 Chevrolet Uplander Questions & Answers

Question edited for clarity. Question moved from Spanish Car company 'Seat', pronounced See-At. Check Fuse 13 (Heated Seats) https://fuse-box.info/chevrolet/chevrolet-uplander-2005-2008-fuses-and-relay ..

Check out this case study on a Chevy Impala for that P1404 code on a new EGR. I only watch the beginning, (too long for me to sit and watch) but seems to be a communication issue. https://www.youtube.com/watch?v=HT4OnP4U0to https://www.google.com/search?q=P1404 https://www.google.com/search?q=P0404 ..

Question edited for clarity and all the typos. Question moved to sub category. Did you disconnect the battery recently? It could be many things, but it could be the security system immobilizer. You should also check for fault codes. When you say 'nothing works inside', do you mean things like the dome light, the radio, and the dash lights? If that is the case, you need a mobile auto electrician. https://www.google.com/search?q=2005+chevy+uplander+security+reset ..

Question edited for clarity. Question moved to sun-category. You have modules issues. For that you need an auto-electrician with a pro grade scan tool computer. They collect data from each module and tell which are causing the issue. Likely to be ECM and BCM issues.

Generic obd 2 system allows access only to systems that affect exhaust emissions and dealer level software is needed for everything else. A fault that affects the exhaust emissions should switch on the engine check light and store a fault code in the memory. While the light is on the engine is operating on the get-you-home programme. When there is a problem, after a thorough visual inspection and ensuring the routine maintenance is up to date, a code reader or scanner is used to read stored fault codes, examine live data and suchlike. The fault code is an invaluable start point in the diagnostic process and repair, but in order to advise you further you need to tell us what the code is...

The transmission speed sensors of normal cars are located near the front and rear of the transmission housing. Check the repair manual for your car. I hope it will help you out.

suspect a problem with fuel system , like the filter needs replaced perhaps

Sounds like a faulty wire set; also possible the wring is improperly installed and the end connectors are not making proper contact with the plugs/control module.

There may be an access hole plug at the bottom of the trim panel you can remove to insert a flat bladed screwdriver into the latch tommanually release it. If no plug there may be an intention in this area where you can drill a hole into the trim panel to insert a screwdriver. Then you can purchase a plug from a Chevy dealership to cover it up.

While there are a variety of reasons your Chevrolet Uplander is overheating, the most common 3 are a coolant leak (water pump, radiator, hose etc.), the radiator fan, or a failed thermostat. A more uncommon reason is your radiator is partially scaled up and under a heavier load, the cooling capacity is not sufficient.

Hmm I don't know what the skreeting sound might be, but your lack of power and spuddering is most likely do to an ignition problem. This van has a V6 and GM V6's use a waste spark system. Many times a spudder or lack of power is due to a failed ignition control module or coil pack. If you have a failed coil pack you should replace the ignition control module as well because it most likely has damaged the ignition control module anyway.

Have you checked the water pump? Also, you may want to check the oil to ensure no water is getting into it. This would be a milky color oil which would indicate a bad head gasket or head. Is your radiator fluid staying at the full level or are you losing fluid? if all of this looks good, you may have air in the system. You can google or search on youtube for ways to clear the engine of air in the cooling system.

I looked into your year and it does not look like a replacement throttle body actuator is available. In case you want to know. The "Throttle Body Sensor" and "Throttle Position Sensor" are all inside the throttle actuator. They can not be separated and replaced. For your year, the throttle body and actuator are sold as an assembly.

ALL TUNES-2008 CHEVY UPLANDER NO START https://www.youtube.com/watch?v=TnIyKf0JiNU 2007 Chevy Uplander No Start https://www.youtube.com/watch?v=PN-zlKn5KRo Starting disabled FIXED!!! Chevy Uplander. I have a 2005 Chevy Uplander that won't start. The problem... https://www.justanswer.com/chevy/6jkas-2005-chevy-uplander-won-t-start-problem.html 2005 chevy uplander hard to start http://www.topix.com/forum/autos/chevrolet-uplander/TALVQR3Q8MKI7M33D/2005-chevy-uplander-hard-to-start

factory remote starter???? Your vehicle has remote start , doesn't work ? Does the vehicle start with the key ? Remote start is a function of a control module - BCM - body control module more then likely . Unless your vehicle has after market remote start . Your best bet take it to a qualified repair shop . The vehicle has a regular starter mounted on the engine ,remote starter is software programmed into the computers on the vehicle . Circuit/System Description Remote vehicle start (RVS) begins as an RF message received by the remote control door lock receiver (RCDLR) from a keyless entry transmitter. The RVS request is sent by the RCDLR to the body control module (BCM) via serial data. The BCM monitors system conditions such as content theft deterrent (CTD), hood ajar status, and body DTCs to determine if an RVS even will occur. If conditions are determined to be acceptable, the RVS message is sent to the engine control module (ECM). The ECM monitors system conditions such as engine control parameters and vehicle theft deterrent (VTD) to determine if engine starting will be allowed. If conditions are acceptable, the ECM will initiate engine starting. During the engine run time in a RVS attempt, before the operator enters the vehicle, the ECM may discontinue engine operation if system conditions require it or a message is received from the BCM requesting the engine be turned OFF. Your best bet ,take it to a GM dealer

Vehicle needs to be hoisted up and front wheels removed and the front frame portion needs to be lowered from vehicle. But after first disconnecting steering column, a/c and other various components. Then once out and accessible to transmission, it then can be removed. Hope this helps you out in your task. Jesus loves you, John 3:16-17 (KJV)

use a scanner to reset the ECM and immobilizer

The fuel system is a returnless on-demand design. The fuel pressure regulator is a part of the fuel sender assembly, eliminating the need for a return pipe from the engine. A returnless fuel system reduces the internal temperature of the fuel tank by not returning hot fuel from the engine to the fuel tank. Reducing the internal temperature of the fuel tank results in lower evaporative emissions. It's inside the gas tank

This will not prevent the car from starting - will cause ABS light, traction control light (if equipped) and maybe weird low speed braking. Usually the fault of the lights is a bad wheel bearing/hub very common. The EBCM (Electronic Brake Control Module) is mounted to the BPMV (Brake Pressure Modulator Valve) located at the left front (lower) engine compartment. It looks like a (thick) flat black box.