20 Most Recent
2005 Dodge Magnum SE Questions & Answers
What does code p2096 mean for 2005 magnum SE?
P2096- Post Catalyst Fuel Trim Sys Too Lean Bank1... It could be the result of bad gas or if you used fuel with a higher content of Ethanol. It could also mean that the post cat. converter O2 sensor on the driver side is bad. I would try filling up with a good quality gas (minimal Ethanol content), disconnect the negative terminal on the battery for a minute or so to reset the MAL (malfunction indicator light) and see if that takes care of it. If the code reappears, you may have a bad sensor, maybe ECU ECM PCM, worst case.... If you happen to need any info or ECU ECM PCM for this current vehicle (as they have a HIGH failure rate) or ANY other type of Car, diesel trucks small and big, SUV DIESELs ANYTHING etc, please call 888-672-4816 or 954-279-2040 and tell them Tim From FIXYA.COM sent you for FREE PROGRAMMING on YOUR NEW ECU ECM PCM DIESEL OR GAS COMPUTER!! Best Regards, -Tim
Rpm , gas , temp guage not working
All of these gauges are digital are controlled by a computer in the instrument cluster. You will need to remove the cluster and send it out for repair by a factory approved instrument cluster repair center. You can find these on line. JUst Goggle "Dodge Instrument Cluster repair"
1978 dodge magnum XE 5.2 ,CARB 2 barrel , lean burn HORROR need to know part on firewall between ballistic resistor and voltage regulator it is orange with 3 wires and has plug in
FIRST OFF , 1978 IS A NO DIGITAL DOCUMENT YEAR.
2000 IS YES. (ON AVG)
so only books exist then paper hard bound books, service manual.
so buy one used there 44 years old. and now have what you need
they be rare.
most folks never hand scanned a 1000 page 44 year old book.
that be (over the top brave) not me!
WOW 1 NO PHOTO POSTED OF THE OBJECT,
And gee 2, nobody drives any lean burn car now. ever.
wow2 , wire coolers all 3 not told ,now that makes reading schematics to you impossible.
wow 3, no problem told is something dead, (i bet yes) but not told.
if was told we can look on pages that have 3 devices related to the problem. not told.
most of these cars where crushed at the $500 federal, crush program. rare now. super rare.
read here (kinda does the job but weak on locations)
https://app.chiltonlibrary.com/home
2005 Dodge Magnum set 3.5L V6 used to be a police car. P0700 and p1775?
https://www.yourmechanic.com/article/p0700-obd-ii-trouble-code-transmission-control-system-malfunction-by-spencer-clayton#:~:text=P0700%20is%20set%20when%20the,or%20normal https://www.engine-codes.com/p1775.html the 700 is the tcm detecting a problem and the problem its detecting is with the tcc the second link has solutions to assist with repair ----also a low battery can cause havoc with trans
Have you heard or read that 3.5L engines in the Magnums blow up?
Dodge magnum engines are like any other make or model. Engines usually only 'blow up' if they have not been maintained correctly and have been badly treated, (driven hard before the engine has warmed up to working temperature. If you want a Magnum go and look at as many as you can BEFORE you decide to buy one. If the vehicle has no documented history WALK AWAY!!
Not sure but it seems the 2006 and 2008 models seemed to be the problem years. There were more than one engine size fitted so the issue could have been with the larger V8 engine.
2007 magnum wagon loud right front end squeak
Check any rubber on your struts or any other rubber that's used for softening/dampering on the steering. I once had a piece of rubber on the front of a car that would squeak when my wife hit bumps going down our driveway, drive my wife crazy and since it was under warranty we made the stealership find and repair it. Only took about 5 trips to stealership before the clowns finally found it.
I have a 2005 Dodge
If it was the key or the theft deterrent system it would have a light on dash with a key symbol I would check the relays in the power dist box for crank and ign make sure there good and if you have another key try it also and it's possible the receiver for tds is bad is is in the column and is around the ign switch
Not finding what you are looking for?