20 Most Recent 2010 Chevrolet HHR LS Questions & Answers

There are two junction connections on the four wire harness that runs from the SDM (airbag controller under driver seat) to the passenger side airbag (I/P module). Once connection is just below the passenger side airbag in the dash and another is behind the driver side kick panel. In my case, the connector behind the driver side kick panel had likely a bit of corrosion and there was high resistance that thre the service airbag message and light on the dash. Once I cleaned this connection, the light was gone and the problem is now fixed.High resistance in either of these connections will throw the B0019 OD code.

under air filter

disconnect either heater hose at the engine, remove radiator cap, slowly pour water in at heater hose untill it comes out radiator

Question edited to full make and model. Changed VIM to VIN. Question moved to sub category. help to fix in the link and a video https://www.google.com/search?q=Hhr+radio+reads+no+VIN ..

They usually hammer the screwdriver into the lock and use the screwdriver to turn the lock in place of a key. Of course they forget about the antitheft system, but some just want to release the steering lock so they can get it onto a low loader and strip for parts. Take off all the plastic and replace the lock. It is a job better left to your local dealership because of removing the hardened steel pin some have and some has a special technique for sliding the cylinder out. The Anti-theft may need reprogramming. This might help https://www.google.com/search?q=hhr+replace+ignition+switch ..

linkage problem. This link might also help: https://www.google.com/search?q=2011+CHEVROLET+Why+doesn%27t+it+go+into+reverse+when+put+in+reverse+or+drive+as+well%3F+&ei=da60YN6gKY3Yz7sP27ivqAI&oq=2011+CHEVROLET+Why+doesn%27t+it+go+into+reverse+when+put+in+reverse+or+drive+as+well%3F+&gs_lcp=Cgdnd3Mtd2l6EAM6BwgAEEcQsAM6AggAOgUIABDJAzoGCAAQFhAeUIqdB1imgQhgnIYIaAVwAngDgAGZA4gBniOSAQgxLjI3LjQtMZgBAKABAaABAqoBB2d3cy13aXqwAQDIAQi4AQLAAQE&sclient=gws-wiz&ved=0ahUKEwier6zYz_PwAhUN7HMBHVvcCyUQ4dUDCA4&uact=5

unplug the snapshot and send it back before it does even more damage! and google problems related to snapshot,you will find thousands of similar complaints!

Replace the cam magnet in the front of the engine.

15 foot lbs.

0.9 lbs.

Your vehicle does not have an orfice. It has an expansion valve.

Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything someone on fixya recommended it to m e and I thank him even today They have full manuals and it's verrrrry cheap

Here is a video of the removal of an axle shaft. Basic tools are needed plus a large socket for the axle nut. https://www.youtube.com/watch?v=qD4arlr9jag http://www.fixya.com/cars/t17796741-right_side_cv_axle_replacement_hhr Also a post about cv questions .

You might try www.ereplacementparts .com or www.1aauto.com i hope this helps. marcus

recheck the timing,valve clearance, run the OBD for any codes to faulty sensors etc

Hello Kenneth...a simple one wire toggle switch will do the trick...the ignition switch pink wire will interrupt the start/crank function but your anti theft system may not like the power disruption during ignition off mode. Always make sure your battery is disconnected while making modifications and carefully research the effects of electrical mods. You can always remove a related fuse ie: (fuel pump) if you are trying to secure the vehicle from another ignition key.

look in the glove box for the code or the trunk. you might find it there. if not, then copy your vin # down and call the dealer for the code.

Shud tell u on the cover or a partplace will showu