2001 Chrysler Town and Country - Answered Questions & Fixed issues


Remove the inner door panel and take out the window holder.

2001 Chrysler... | Answered on Feb 26, 2019 | 34 views


I believe three bolts holds the solenoid to the front top of the transmission and there is a metal plate with 2 gaskets. Usually the gaskets are just stuck in place. Before you remove the solenoid be sure to take a long neck blow gun and blow out behind the solenoid as dirt and debris tends to pack in there. once its clean, remove the wiring, remove the bolts and take a small pry bar and rock the valve pack away from the case. Once it starts to move you should be able to rock it back and forth lightly til it lifts up and off the tranny. Clean with a razor blade, trying not to let any gasket paper fall into the holes and then install the new pack. I think you have to re-use the metal plate so you'll have to scrape the gaskets off that also.
Hope this helps

2001 Chrysler... | Answered on Jan 22, 2019 | 44 views


Paint code should be in inside of door well. Go to automotive paint store or body shop they will help you

2001 Chrysler... | Answered on Mar 05, 2018 | 30 views


You are looking at the problem wrong.
The computer controls the sensors after they send information to the computer this regulates how the engine runs under varies conditions .
What you need to do is get the codes read auto parts stores will do this for free or buy a code reader for 40.00 bucks .
This will tell you witch sensor is bad and also erase old codes from your MIL -computer

2001 Chrysler... | Answered on Aug 14, 2016 | 38 views


sounds like you have a stuck sensor

2001 Chrysler... | Answered on May 02, 2016 | 29 views


you may have a bad thermostat have it check if you are not able too sometimes the switch go bad or the rod that closes the door may be off

2001 Chrysler... | Answered on Dec 17, 2015 | 56 views


Check make sure the lock is not engaged for pass window, the drivers side switch is the master switch. make sure all connections are good there.

2001 Chrysler... | Answered on Oct 18, 2015 | 149 views


after removing the battery or battery lead there are problems created in the ECM and CPU program
It is a good idea to run a scan tool and reset the program and see what happens after that

2001 Chrysler... | Answered on Aug 22, 2015 | 218 views


First you will need to have the system evacuated so there is no longer refrigerant in the system

Next remove the rear seats or stow them. Then remove all the trim panels from the passenger rear of the vehicle. You will then be able to see the rear HVAC assembly.

Jack up the vehicle and support it properly. remove the nut that holds the rear lines to the expansion block.

Remove the heater core form the HVAC module with the cooling lines still attatched. Remove the HVAC module from the vehicle.

You will then be able to replace the rear evap core/tubes/expansion valve.

Get the kit from the dodge dealer. It will make life very easy.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

2001 Chrysler... | Answered on Aug 14, 2015 | 144 views


You can bypass it by installing an immobilizer bypass for aftermarket alarms like: DEI CHTHX2 CHRYSLER MUX Type Plug Play Harness XK09 Bypass Module Xpresskit

2001 Chrysler... | Answered on May 08, 2015 | 369 views


output speed sensor is the same thing. Sending a picture. It unscrews. Look straight down between the radiator and transmission.
25657330-cjo2jczcqc4pn4ns3k2s1t1v-3-0.gif

2001 Chrysler... | Answered on Apr 21, 2015 | 708 views


Thread Correct anti freeze for 2005 Town Country

this covers your generation minivan 2001-2007

HOAT are the letters you're looking for if you aren't buying dealership coolant

seems like people like Zerex G05 as the alternative

2001 Chrysler... | Answered on Apr 04, 2015 | 274 views


Check connections to Alternator and Battery. If probably connected, have someone check the Alternator output. If still good, check fuse.

2001 Chrysler... | Answered on Feb 24, 2015 | 180 views


from the front or back of the head light , there will be 2/3 adjusting knobs / screws . Place the vehicle on a level surface about 3 feet from a plain coloured wall. You will see the centre of the beam( High beam). The centre of the beam is to be at the same height as the centre of the head light lense and properly adjusted pointing slightly to the passenger side of the vehicle . This prevents full beam in the eyes of oncoming cars.

2001 Chrysler... | Answered on Apr 21, 2014 | 85 views


Open up the hood and you will see the adjustment screws on the side and top of the lens assembly. You can look up what the specifications are for alignment online and use your garage door for adjustment.

2001 Chrysler... | Answered on Apr 21, 2014 | 27 views


moved you out of computers, to Chrysler Town and Country


the cars service manual covers this and varies by engine, and drive train on all cars made these rules.
RTM
read the cars, factory service manual.

Chrysler Town... | Answered on Apr 26, 2019 | 16 views

Not finding what you are looking for?
2001 Chrysler Town and Country Logo

45 questions posted

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...