Question about Polaris ATV

1 Answer

The cv boot on my bombardier trackster needs replacing. where do i begin .behind The right front tire there is an axle with 2 rubber boots on them. the one closest to the wheel is ripped. how does the axle come off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Take off the wheel. Take off the large hub nut. Unbolt either the upper or lower a-arm (which ever is easier) from the bearing hub. Now slide the outer axle end out of the bearing hub. The inner axle end should easily unplug from the gear case with gentle prying. To replace the outer boot you have to take off the inner boot first, remove the clip inside the cup , and slide the bearing out. Remove the external circlip that holds the bearing on and slide the bearing off. remove the old boots by sliding them off the axle. Reassemble in reverse order . You may need a special tool for installing the boot clamps.

Posted on Aug 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace cv boots on atv


  1. First jack up vehicle.
  2. remove tire/rim
  3. remove cotter pin and castle nut from the end of the axle.
  4. disassemble spindle from upper/lower ball joints'
  5. separate spindle from axle by pulling spindle away from the vehicle.
  6. with two hands grasp axle and pull firmly to remove axle assembly from differential.
  7. remove torn cv boot, clean all old grease from cv joint.
  8. apply new grease and install new boot.
  9. secure clips on cv boot.
  10. Reassembly is reverse of disassembly.
  11. Consider purchasing the service manual for your make /model of atv from amazon. This manual will have step by step instructions and pictures for any repair or maintenance that you will need to perform.

May 15, 2016 | ATVs

1 Answer

Why is my front driver side tire binding in 2 wheel drive


Probably dirt or grit got in to your CV joint check cv joint for tear or small rip

Feb 01, 2016 | Polaris 2014 RZR 4 900 EPS Orange Madness...

1 Answer

My front axel is turning but the wheel is not tried replacing armature plate but made no difference what could be the problem


Have you checked the splines on the wheel hub end of the cv joint? They're splined - and when the splines wear down - the cv joint will turn - but you're tire won't. If you shoot me your make and model and I have the manual - I'll shoot you the minimal clearance on those spines. If it's not the splines (male) on the cv joint - it's probably the female splines of the hub

Nov 13, 2015 | ATVs

1 Answer

Replace outer front cv boot


Jack it up and take the tire and hub off and then you can take the boot off from there. you will need the tool to replace the boot band.

Mar 21, 2014 | kawasaki 2007 Mule 3010 Trans 4x4

1 Answer

Bombardier traxter removing starter


Some starters are in front of motor some are just behind cylinder on top of crankcase

Nov 06, 2013 | ATVs

1 Answer

Cv axle interchange 2004 - 2005 polaris sporstman 400


The "upgrade" can be done but it ain't cheap! The outer hub has to be a 2005 for clearance of the CV joint and there are clearance problems around the front pumpkin. If you keep the angle to near stock, the knuckles are very reliable. Make them bend too far, with a lift kit and they will break.
For brakes: EBC Severe Duty FA159SV in the front and FA314SV in the rear

Mar 28, 2017 | Polaris ATV

Not finding what you are looking for?
Polaris ATV Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

john h

Level 3 Expert

10942 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...