Question about kawasaki 2012 Mule 4010 4x4

Open Question

Oil drain plug location on a 4010 4x4 Kawasaki mule

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mule 3010 has no power. in low or high it goes maybe 9 mph, has new pump, spark plugs, checked the vents, nothing is helping


What is the compression? This leads me to think you may have more of an internal issue.

Have the compression checked, with throttle wide open, then repost with the results.

May 20, 2017 | kawasaki 2005 Mule 3010 4x4

1 Answer

I have a 2003 kawasaki mule model 3000 it wont say running at idle what to do


Full tune up and carb clean .get new plug,air filter.oil Chang ,carb clean and adjustment.that should do it.,., try fuel filters and test fuel pump see if it's functioning properly.,.

Dec 10, 2016 | kawasaki 2005 Mule 3010 4x4

1 Answer

What is the best way to winterize mule stored in a garage


There's a drain screw on the bowl of the carburetor - either run the gas out - or turn the valve to off and drain the gas in the carburetor. I also take the spark plug out and spray on top of the cylinder and all around - anything metal. GETSOME is a product out of Florida that actually works. Disconnect the battery and hook the battery up to a 2amp tender/not charger - you'll need the battery tender that keeps the voltage correct but doesn't over charge - reverse when the seasons change and you should be good to go -

Nov 16, 2015 | kawasaki 2008 Mule 3010 4x4

1 Answer

Where is the neutral safety switch for a kawaski 3010 mule


Kawasaki Mule Update - YouTube

? 2:16
www.youtube.com/watch?v=Fw_jeQUU6Hw
Jan 25, 2013 - Uploaded by Penguinboy1995
solenoid is reading battery voltage and the constant hot, it is not sending the 12 volts from the switch to the ...

Sep 19, 2015 | kawasaki 2005 Mule 3010 Trans 4x4

2 Answers

Pushing oil out fill plug


too full then or you have blown head gasket

Apr 17, 2015 | kawasaki 2005 Mule 600

1 Answer

HOW DO I REMOVE FRONT HUB ON MULE 2005


first off secure the buggies tyers with chocks either a brick or some wood blocks then proceed to jack up the tyre and axel you would like to remove - remove the tyre proceed to remove the hub once you have established where the bolts _ cotter pin etc are located

May 27, 2014 | kawasaki 2005 Mule 610 4x4 Camo

1 Answer

What is possible cause that a mule 3010 kaf620e6f will not hold idle?


Air leak .dirty air filter.,.fouled plug.,.bad gas.,.dirty carb?fuel injection? Bad fuel filter ,fuel pump test fuel pump that's the general stuff.go from there

Apr 28, 2014 | kawasaki 2006 Mule 3010 4x4

1 Answer

Kawasaki mule 3010


Check the starter or solenoid.

Apr 27, 2013 | kawasaki 2008 Mule 3010 Trans 4x4

1 Answer

Kawasaki Mule 1999 Model


Hello Anon..
First, I would check to make sure the carbs are getting fuel, and then fuel getting into the cylinders. Your question about low oil - did you let it get low and then it quit? ...
If you put oil into the cylinders and only got 100psi, this might be your problem. You should be pumping around 120+psi without putting anything into the cylinders... Recheck the compression.= .take out all spark plugs...screw the gauge in until the o-ring seats, hold the throttle wide open while spinning the engine over for about 5 seconds... you should get 120psi +/- 10psi.
If you are getting less than 100psi.. it might be time for a rebuild..

May 24, 2017 | kawasaki 2005 Mule 3010 Trans 4x4

Not finding what you are looking for?
kawasaki 2012 Mule 4010 4x4 Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki ATVs Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Lawrence Oravetz

Level 3 Expert

9742 Answers

Glenn Smart
Glenn Smart

Level 3 Expert

818 Answers

Are you a kawasaki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...