Question about ATVs

Open Question

Can you override rev limiter on 2001 grizzly 600 ,if so ,how?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 112 Answers

SOURCE: reverse speed limiter

Could be a problem with the switch inside the throttle housing.

Posted on Apr 02, 2009

  • 22 Answers

SOURCE: how do i disconnect a rev limiter on a 2001

Not a good idea. Its a big motor with big pistons and you get those big suckers pumpin faster than yamaha intended and you'll end playing "Which of these pieces in my bottom end USED to be in my top end"

Posted on Jul 23, 2010

  • 3567 Answers

SOURCE: 2001 600 grizzly uses engine

You didn't say the bike was leaving a large white cloud of smoke when riding so the only other reasonable alternative is compression getting past the piston rings is forcing the tranny oil out of the crankcase breather and onto the roadway. Please rate my answer. Thanks.

Posted on Jul 01, 2011

exporteh
  • 6 Answers

SOURCE: yamaha grizzly 600 back fire when reving engine

Try checking the ignition timing,then the valve timing. Should take care of your prob.

Posted on Dec 24, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 Yamaha Grizzly 600 runs for 5mins. and dies. Engine won't turn over for short period and then starts. This cycle continues.


fuel flow to the carb is slow. fills the bowl, runs till its dry. pause while it refills slowly, repeat.

Feb 21, 2017 | ATVs

1 Answer

2002 660 grizzly red light reverse light comes on then it starts to cut out


sounds like your reverse sensor is bad and the cdi limits rpms while in reverse as a safety thing.

Dec 06, 2016 | Yamaha 2004 Grizzly 660 Auto 4x4

1 Answer

Yamaha Grizzley 600 1998. starts with pull start and runs well. The electric start turns the engine over, starts periodically, sounds like an intermittent electrical issue, any suggestions? Thx RB


pull the starter and have it bench tested
it appears to drawing excessive current and removing power from the ignition circuit
pulling on the cord doesn't have that current draw so it starts easily
have the battery load tested as it may not be capable of running starter and ignition

Jul 20, 2016 | ATVs

1 Answer

2005 Yamaha Big Bear 400. How do I replace rear brakes?


Removing The Rear Brake Drum & Shoes on Grizzly 600 ...

? 5:04
www.youtube.com/watch?v=n5oO7v3nT6s
Mar 11, 2012 - Uploaded by myquadrepair
Removing the rear brake drum & shoes on Yamaha grizzly 600. ... Yamaha Big Bear Oil Change and More! - Duration: 10:43. by jfrost77hd ...

HONDA FOREMAN REAR BRAKE CHANGE PART 1 ...

? 11:49
https://www.youtube.com/watch?v=xQanZdlDCI0
Jul 17, 2012 - Uploaded by 400EX99N
HOW TO CHANGE REAR BRAKES ON A HONDA ATV. ... is this about the same for a 2004 yamaha big bear 400? Read more Show less.

Nov 03, 2015 | ATVs

1 Answer

Yamaha grizzly 600 back fire when reving engine


Try checking the ignition timing,then the valve timing. Should take care of your prob.

Dec 24, 2014 | ATVs

1 Answer

Yamaha grizzly problems


remove and clean carb... and clean it very well making sure nothing is corrodid

Aug 28, 2014 | ATVs

1 Answer

Why does my Yamaha grizzly 700 engine brake fail going down hill


If you're in to low a gear, the clutch might be slipping under stress from high revs. You might need a new clutch or stronger springs. Try using a higher gear and use 50% braking.

Jun 21, 2014 | Yamaha 2007 Grizzly 700 FI 4x4 Auto...

1 Answer

Backfires when you try to rev up engine,


check fuel flow and check spark at spark plugs

According to an "ATV Rider" 2009 article, "When the Grizzly was introduced in 1998 as a 600cc machine, the top was blown right off the displacement wars of the time."
It was replaced in 2002 with Yamaha Grizzly 660, an even bigger engine derived from the well-established all-terrain vehicle (ATV) Yamaha Raptor 660R.
Grizzly's 660 cubic centimeter (cc), four-stroke, liquid-cooled single overhead camshaft, five-valve engine performs well in open country, but sometimes it causes serious problems for owners.
Before you call a Grizzly dealer, however, trying a few tricks in your garage can save you a lot of time and money.

Check the fuel level.
Locate the fuel meter indicator on top of the multifunction display.
If it does not work properly, open the fuel tank, and push the Yamaha 660 Grizzly side to side.
Ensure the fuel is not contaminated by water or rust.
If you have not driven your Grizzly 660 for a long time, drain the tank completely, and fill it with a fuel tank cleaner.

Check fuel hoses for cracks or leakage.
The hoses should be soft and simple to bend.
Replace those that show any sign of wear.

Check the compression.
Screw a compression tester into the spark plug hole, and press the electric starter button.
If no compression exists, contact a Yamaha dealer.
Wipe wet or dirty electrodes with a dry cloth.
The spark plug gap should be checked regularly

Correct the spark plug gap.
Measure the gap with a wire thickness gauge.
If necessary, adjust it to 0.8mm using a screwdriver or replace the spark plug.
Use only a Yamaha-specified spark plug.

Check the Yamaha 660 Grizzly's battery.
Operate its electric starter.
If the Grizzly starts quickly, then its battery is in good condition.
If the engine turns slowly, check the battery lead connections, and you may need to change the battery.
If the engine still does not eventually start, your Grizzly is beyond home repair.


Jul 23, 2013 | Yamaha 2005 Grizzly 660 Auto 4x4

1 Answer

Yamaha grizzly 600 not firing


Check spark clean the carb check valve clearances if none of those you have an electrical problem

May 16, 2010 | RTO 200cc Full Size Four Wheeler ATV

Not finding what you are looking for?
ATVs Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top ATVs Experts

john h

Level 3 Expert

11057 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

 Scott Tx
Scott Tx

Level 2 Expert

516 Answers

Are you an ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...