Question about ATVs

1 Answer

Install selunoid

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

The solenoid follow your positive and negative from the battery , it should connect directly to the solenoid first . two bolts hold it in, remove and replace .

Posted on May 28, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a sportsman 400 H.O and I need to know how to install a fuel vent check valve, help!

the check valve is a one-way valve, it will allow fuel to overflow but not allow water/etc/.. back into the fuel system...
To know which way to install the valve in the vent line..try blowing through it...this will tell you which way to install it..

Oct 21, 2017 | ATVs

1 Answer

How can I install a pull start kit?

google search Yamaha Grizzly Pull Start Kit instructions and choose images to get exploded view.
link is the install, should be the same as yours.
press the helpful button

Yamaha Big Bear 350 recoil start install

Jan 31, 2016 | Yamaha 2011 Grizzly 450 Auto 4x4

1 Answer

How do i set timing on a 2000kawasaki prairie

This procedure is for 200 Kawasaki Prairie 400
1:on the flywheel cover, remove the pull starter asembley so you can turn the engine over by using a wrench. on that same side, remove the timing inspection plug. it will be on teh side of teh flywheel cover, and have a large flat blade screwdriver mark or allen hole you use to unscrew it.
2:with the inspection plug removed, slowley turn the engine untill you see a "F" and a line. from there, rotate the engine very slowley untill you see a "T." JUST after the "T" there is a line. you want the mark inside the inspection plug hole to line up with that line after the "T."
3: with the bottom end now timed, you will install the cam into the head. when you set the camshaft into the head, do so with the lobes pointing directly down. after the cam is installed, then install the cam sprocket and make sure the lines on it are directly left to right. the lines will end up lining up with the level surface of the cylinder head surface. ater you have installed the cam and sprocket, look again at the inspection hole in the flywheel cover to recheck that the bottom end is still on time.
4: once the cam is installed, and the sprocket is installed on it, you will see the lobes point down, and the cam sprocket lines are from side to side. then yo uwant to install teh cy;inder head cover.
5after the head cover is installed, install the cam chain tensioner, and slowley rotate the engine to ensure the valves and piston do not contact. USE HAND TOOLS TO ROTATE ENGINE, NOT ELECTRIC STARTER!! the electric starter will cause damage if the timing is off.

Feb 11, 2015 | ATVs

1 Answer

How to install a 50 cc carburetor on a 4 wheeler

best place t go is youtube and if you cant find your watching any small motor video will help but you need to watch one of the same engine if yours is 2 stroke then watch a 2 stroke video and same as 4 stroke carbs are different hope this helps

Sep 16, 2014 | ATVs

1 Answer

Removal and installation of stator

Have you tested the stator to make sure it is bad?
You have to remove the left side cover (if you sitting on the ATV)
to replace the stator and a couple things may or will fall out when you remove it unless you have done it before get a manual

Jul 15, 2014 | Arctic Cat 2006 500 4x4 Automatic

1 Answer

How would you return to factory settings?

if you are talking about the fuel injection system after installing an exhaust system and fuel management computer its easy. Install all the stock components and remove the fuel management computer. The fuel management computer plugs get plugged back into the fuel injector, throttle body sensor, and factory CDI

May 06, 2014 | ATVs

1 Answer

Carburetor installation

I'm sorry, if this isn't simply, openly, obviously, easy for you... take it to a professional.

Apr 17, 2014 | ATVs

1 Answer

I need to install a key ignition switch on 4 wheeler

unscrew and unplug old one, reverse to install new one.

Jan 18, 2014 | ATVs

1 Answer

Arctic How To Install recoil

I assume you mean recoil starter, yes? It can be purchased as an assembly or in individual pieces from the dealer. I checked google and the instructions with diagrams can be found. good luck an be careful if you choose to just replace parts, that spring can be tricky.

Oct 26, 2013 | Arctic Cat 2008 366 4x4 Automatic

Not finding what you are looking for?
ATVs Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top ATVs Experts

john h

Level 3 Expert

12744 Answers


Level 3 Expert

77169 Answers

 Scott Tx
Scott Tx

Level 2 Expert

558 Answers

Are you an ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides