Question about Polaris 2007 Sportsman 700 EFI

1 Answer

My display has the wrench icon and the time icon and it says "OFF" on the display on the dash. What does this mean? and how do i get it off?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Programmable service interval
The purpose of the programmable service interval is to provide the consumer and dealer with a convenient reminder for routine maintenance. When your vehicle leaves the factory, this feature is set at 50 hours. You must enable the programmable service interval before it
can be used.
Once the service interval mode is set with the hours when service is due, the hours of actual engine operation are subtracted from the set
hours until 0 is reached. When the counter reaches 0, the wrench icon will flash quickly for 5 seconds each time the vehicle is started as a reminder that the periodic maintenance is due.
To set the hours, press and hold the mode/override button until the wrench icon flashes. When it begins to flash, release the button. The setting will increase by one hour each time the button is pressed.
Pressing and holding the button will allow the numbers to escalate much faster. When the desired time increment is displayed, release the button and wait for the wrench to stop flashing. When the wrench stops blinking, your service hours are set.
NOTE: If you scroll past the intended number, hold the button down until the count turns over to 0. You can then reset the number.
If the service interval is enabled on your ATV and you wish to turn it off, toggle to the service interval mode. Press and hold the mode button for approximately 7 seconds until the word OFF appears in the
Rider Information Center.

Posted on May 18, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The led readout display does not display anymore. the fuses check fine cable and plug adapters look fine. what else is there to look at to fix?


Jeff, Recheck fuses/relays, probe dash wire to see if you are getting power up to dash, if not then fuse or wire broke. If you are getting power into dash then display is faulty and needs repaired or replaced. Check the attached links,Manuals and guides, Good luck with your Bike
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How to Diagnose Motorcycle Electrical Problems Dennis Kirk Inc
ATV TROUBLESHOOTING AND MAINTENANCE
Service Manuals for Download in PDF

Mar 04, 2016 | ATVs

1 Answer

What is the meaning of the wrench with the number 1 on my 2014 honda foreman 500


The vehicle handbook is the best source of that information.

Oct 06, 2015 | ATVs

1 Answer

Hi there is a wrench symbol displaying on the gauge cluster on my honda foreman 2014 atv what does it mean


That is equivalent to a "Check Engine" light, meaning that a condition exists which requires attention. Check all fluid levels, and readout codes from the ECU as a starting point for diagnosis.

Mar 09, 2015 | Honda 2014 FourTrax Foreman 4x4 ES

1 Answer

When a wrench comes up flashing where you start and the atv will not start what does this mean?


You need to pull the Code and see what it is telling you. It is a Mechanical Issue.

Sep 22, 2014 | ATVs

1 Answer

What does the error code PO119 mean on my 2013 arctic cat 500 atv mean


From Repair Pal:

Auto Systems and Repair

Engine Coolant Temperature Circuit Intermittent Our emissions expert has put together the following information about the P0119 fault code. We have also included diagnostic procedures you can take to your repair shop if the mechanic is having difficulty analyzing the code.
OBD II Fault Code
  • OBD II P0119
Fault Code Definition
  • Engine Coolant Temperature Circuit Intermittent
What does Mean?The Engine Coolant Temperature Sensor measures the rise and fall of the Engine Coolant Temperature. This provides critical data needed for the Powertrain Control Module (PCM) to control the Air Fuel Ratio, the Ignition Spark Timing, the cooling fans, and many components of the Emissions Control Systems. The Engine Coolant Temperature Sensor converts the coolant temperature into a voltage that is high when the engine is cold and low as the engine warms up.
Code P0119 indicates an intermittent voltage input from the Coolant Temperature Circuit to the PCM.

Sep 16, 2014 | Arctic Cat 2013 500 TRV Core

1 Answer

520230. 31520193. 7Polaris 550 Xp eps 2009About 20 hours on unitStored indoorsI understand one code is Idle air and the other is power steering is disabled or not functioning. First I would try and...


Diagnostic Mode
The diagnostic mode is for informational purposes only. Please return your ATV to your dealer for all major repairs.
As long as the gauge is in the diagnostic mode, the wrench icon will remain lit.
To leave the diagnostic mode, turn the key switch off and on.
NOTE: Any movement of the tires will also take the machine out ofthe diagnostic mode.
To enter the diagnostics mode:
1. Turn the key switch off and wait 10 seconds.
2. Set the park brake and shift the transmission to neutral.
3. Hold the mode/reverse override button and turn the key switch on.
4. Release the switch as soon as the display is activated.
The initial screen display refers to the software version installed in
your ATV. This information is displayed briefly.
Use the mode/reverse override button to toggle through the diagnostic
screens.

Screen 1: Battery voltage

Screen 2: Tachometer

Screen 3: AWD diagnostic
This gauge indicates whether or not current is flowing through the
AWD coil (only on models with switchable AWD).

Screen 4: Gear circuit diagnostic
This screen displays the resistance value (in ohms) being read at thegear switch input of the gauge.
46 FEATURES
Instrument Cluster
Rider Information Center
Diagnostic Mode

Screen 5: Programmable service interval
The purpose of the programmable service interval is to provide the consumer and dealer with a convenient reminder for routine maintenance. When your vehicle leaves the factory, this feature is set at 50 hours. You must enable the programmable service interval before it
can be used.
Once the service interval mode is set with the hours when service is due, the hours of actual engine operation are subtracted from the set
hours until 0 is reached. When the counter reaches 0, the wrench icon will flash quickly for 5 seconds each time the vehicle is started as a reminder that the periodic maintenance is due.
To set the hours, press and hold the mode/override button until the wrench icon flashes. When it begins to flash, release the button. The setting will increase by one hour each time the button is pressed.
Pressing and holding the button will allow the numbers to escalate much faster. When the desired time increment is displayed, release the button and wait for the wrench to stop flashing. When the wrench stops blinking, your service hours are set.
NOTE: If you scroll past the intended number, hold the button down until the count turns over to 0. You can then reset the number.
If the service interval is enabled on your ATV and you wish to turn it off, toggle to the service interval mode. Press and hold the mode button for approximately 7 seconds until the word OFF appears in the
Rider Information Center.

Jun 28, 2013 | Polaris 2009 Sportsman 550 EFI XP With EPS

Not finding what you are looking for?
Polaris 2007 Sportsman 700 EFI Logo

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

john h

Level 3 Expert

11057 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...