Question about kawasaki 2012 Mule 4010 4x4

1 Answer

Glow plug light does not come on...will not start ...need to replace glow plugs ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Filmmaker:

    Uploaded 5 video answers.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor
  • 70 Answers

Check under the seat in the fuse box to see if you have a bad fuse

Posted on Jun 05, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a Polaris 800 and when I turn the key to start it, I hear one click each time. Thank you


Typical of a flat battery. Put the lights on, turn the key, and if the lights turn to a glow worm, it is the battery.

If not that, number one would be the solenoid and number two the starter itself.

Apr 17, 2017 | ATVs

1 Answer

Why no headlights or panel lights, except in reverse?


If no bad fuses or relays, it has to be a plug or bad wire. take all plugs apart and reconnect.

Feb 16, 2016 | ATVs

1 Answer

What makes the DFI light come on but the engine still runs but seems to run slow


More than likely you have either a bad coil or the rocker arm has slipped off. Pull each plug, Check plug. If 1 is fouled, that cylinder is where the problem is. Check for spark on each cylinder, If one has no spark, replace the coil (there are 2). Replace only the bad one. Before replacing the coil, check for compression, if on is real low, pull off the rocker cover and check for valve action.

Jan 30, 2015 | kawasaki 2011 Mule 4010 4x4

2 Answers

2010 sportsman 500 hd runs then dies turns over won't start


My opinion, it's running rich and letting it idle for 5 minutes doesn't help. Whether it's carbed or EFI, when the machine is cold, it needs more fuel. As engine temperature increases, it doesn't need as much fuel, and the carbon that started building up on the plug is burned back off. When a machine isn't ran for very long, carbon deposits continue to build on the plug. The carb itself may need to be rejetted/adjusted, it it's running rich,

Aug 12, 2014 | Polaris 2010 Sportsman 500 H.O

3 Answers

I can't get my atv to start it turns the spark plug is firing and the gas is flowing but it will'nt start


check the compression, REPLACE the spark plug with a new one, clean or have the carb professionally cleaned. compression should be at least or more than 100-110 lbs.

May 22, 2014 | ATVs

1 Answer

WIRES FOR TAILLIGHTS ARE CUT, IT FRIED THE JUNCTION PLUG GOING TO THEM HOW DO i REAPIR IT AND KNOW WHICH WIRES GO WHERE.THEY'RE ALL BURNED NOW


get a factory wiring schematic first ... but find out where the wires shorted... ..? somewhere under the seat, at the junction plug, in the tail light??

May 06, 2014 | ATVs

1 Answer

Atv 06 king quad 700 plug fails while riding i clean it ,sand blast no start put new plug in starts up


Fuel mixture is off. The ceramic on the plug absorbs the fuel and shorts out the plug. The reason only a new plug will work.

Mar 31, 2014 | ATVs

1 Answer

Helpme!


Check for spark at spark plugs then check fuel and fuel filter .

Troubleshooting a small Petrol engine that won't start requires a series of short tests and the process of elimination.
Understanding the principles of how a small engine operates is helpful but not necessary.
Proper disposal of hazardous liquids will be required.
The knowledge gained in the performance of this procedure can be applied to many different types and sizes of internal combustion engines.
The average weekend mechanic can complete the process in about an hour.
Put on the safety glasses.
Remove the gas cap and check that there is gas in the fuel tank.
Look at the inline gas cutoff valve located below the gas tank on the fuel line and make sure it is in the on position, with the knob turned straight in line with the fuel line.
Look at the spark plug and check that the wire is securely plugged onto the plug.
Try to turn the spark plug by hand and make sure it is screwed firmly into the hole.
Look at the ground strap by the spark plug and make sure it is not touching the spark plug.
Look at the kill switch located by the controls and make sure it is in the run position.


Remove the air filter by unsnapping its box-like cover or removing the wing nut that holds it onto the carburetor.
Lift the air filter out of the holder and set it aside.
Spray a shot of starting fluid from the aerosol can into the empty air filter area of the carburetor and try to start the engine.
Let the engine run about 30 seconds or until it dies.

Eliminate the electrical system as the cause of the problem if the engine started right up, ran a few moments, and quit.
Remove the gas line from the carburetor by loosening its hose clamp with the screwdriver kit.
Hold the fuel line over the clear glass container and let some gas run into it.
Look at the gas, checking for water and impurities.

Drain the gas tank if the gas looked impure.
Remove the gas filter from the fuel line by loosening its hose clamps with the screwdriver kit.
Replace the gas filter with a new one if the gas did not run into the glass at a rapid pace.
Reinstall the gas line and gas filter.
Fill the gas tank with new gas.

Find a small drain bolt located on the very bottom middle of the carburetor.
Place a small container that gas won't melt under it and remove it with the wrench kit.
Let the old gas drain out of the bottom until the new gas starts to flow out. Screw the drain bolt back into the bottom of the carburetor.

Clean up any spilled gas off the motor and elsewhere with the shop rag.
Place the rag in the metal bucket a safe distance from the work area.
Clean the air filter with warm, soapy water if it is the spongy type, or replace it with a new one.
Install the air filter. Start the engine.

Unplug the spark plug wire from the spark plug if the engine did not start.
Hold the insulated part of the spark plug wire with one hand and place the bare part about 1/4 inch away from the top of the spark plug.

Try to start the engine and watch for a spark between the wire and the plug. Replace the spark plug wire with a new one if it shocked you through the insulation.
Remove the spark plug using the spark plug wrench and replace it with a new one if there was a spark.
Try to start the engine. Let the engine run until it performs smoothly.

Do not do anything else if there was no spark, as the trouble is inside the internal workings of the engine and requires professional repair and tools.
http://www.popularmechanics.com/cars/how-to/maintenance/1272351?click=main_sr

Jul 11, 2013 | ATVs

6 Answers

ATV will pull start but won't electric start? It just clicks...already replaced solenoid.


sounds like a dead battery, if not than its probably the rectifire. if you need me to help i can.

Jul 18, 2009 | RTO 125cc Full Size Adult Quad ATV

Not finding what you are looking for?
kawasaki 2012 Mule 4010 4x4 Logo

Related Topics:

506 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki ATVs Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Lawrence Oravetz

Level 3 Expert

9324 Answers

Glenn Smart
Glenn Smart

Level 3 Expert

798 Answers

Are you a kawasaki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...