Question about Polaris 2014 Ranger 570 EFI

Open Question

Need to hook up linkage from throttle to governor and adjust governor arm

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 Polaris sportsman 700 efi has a shift lever problem. It says in low where the high position should be. is it stripped or is there a way to adjust it?


your shift linkage could be out of adjustment. the two rods that run to your transmission. try disconnecting one and see if it shift *(without the engine running), then do the same thing for the other. if it shift into high without the low gear shift linkage disconnected, then they are out of adjustment.

Nov 03, 2017 | ATVs

1 Answer

250 trail boss high idle cant ajust


If the screw(s) on the carb make no difference... the throttle cable may need to have slack added... IF there is an adjustment at the handlebar... start there and give it slack -- The throttle should be able to move without revving the engine.... if there is not slack or play... adjust the cable until there is.- the next adjustment is at the top of the carb, where the cable goes in -- ....If this does not help, you may have pinched the throttle cable, or have an air leak or the intake valves are too tight-(usually manifest in a "slow to idle" - "run away idle" situation) .....

Aug 22, 2017 | ATVs

1 Answer

My 1999 Kawasaki prairie kvf 300 runs smooth but will not rev all the way up to full rpms.


Check that the rev governor/throttle cable adjuster screw has not slipped out of adjustment (lock nut vibrated loose).

Apr 05, 2017 | kawasaki 2005 Prairie 360

1 Answer

REPLACING CONTROL PLATE ON FH601


Alvin, you need a manual,Check the attached links,Manuals and guides, Good luck with your Bike
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

ATV Service and Repair Manuals
Service Manuals for Download in PDF ATV TROUBLESHOOTING AND MAINTENANCE

Mar 04, 2016 | ATVs

1 Answer

1998 polars 500 dies wont start back


Try adjusting you mixture a little richer, 1/8 turn on the fuel screw. If this doesn't help get to idle, you will need to rebuild the carb. make sure you get a complete kit to include the float and throttle springs as well as jets and gaskets. Write down your initial mixture settings and try them again on your rebuilt carb. Should be fine. Bending float arms for travel length is tricky, be careful as they can easily break off making them useless. The rest of the process is pretty straightforward. Ensure you place the needle jet keeper ring on the correct groove and the throttle moves smoothly against the spring tension on the cable above the needle valve.

Mar 03, 2015 | ATVs

1 Answer

I bought a 1995 Polaris Sportsman not running they put i different engine in it now it will try to run. will i need to put on different CDI box?? and how can I find out what the engine came out of


You need to call Polaris of send them an e-mail on their website. They will be able to tell you exactly which model year and model the engine came from by the serial number. They may be able to tell you about the CDI box. If everything looks good as far as the parts interchange, and timing adjustments, then rebuild the carburetor with a new float and throttle spring. be careful to put the keeper clip on the correct groove of the needle valve and be extra careful when bending the float arm for proper travel. (Motorcycle shops have a special tool for doing this if you want absolute precision.)

Feb 26, 2015 | ATVs

3 Answers

What is the problem my ATV polaris 400 is stuck in reverse


if real cold there it could be froze . try using a heat gun around the shifter area or hot water then lift on the shift arm

Feb 21, 2015 | Polaris ATV

1 Answer

Continuous high idle and idle screw no help


Does your artic cat have a carb cable if so it will have an adjustment or a clamp on the cable where it attaches to the linkage..check make sure it is set to low idle..and your idle screw is adjusted to low idke..meaning cable adjusted to lowest possible position when the throttle is released..then make your final adjustment using you idle screw..good luck

Oct 22, 2014 | ATVs

1 Answer

Honda atv troubleshooting


The neutral lights is not going out until the atv goes into gear. Look over the shift levers and rods that puts the vehicle into gear. Take the shift linkage loose from the engine and see if moves by itself. If all the linkages move except when attached to the engine, then the linkages could be out of adjustment (if it has multiple linkages like 4 drive) or the engine has some internal issues like trans problems or other related to the shifting mechanisms.

Apr 07, 2014 | ATVs

1 Answer

It starts and runs fine but has no top end. Topping out at about 8mph.


check to see if the throttle governor screw is set to far in not alowing you to press throttle all the way in it should be on your handle bar were the thumb throttle is

Sep 01, 2013 | Polaris 2004 Predator 50

Not finding what you are looking for?
Polaris 2014 Ranger 570 EFI Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

john h

Level 3 Expert

13723 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Wade Mobley
Wade Mobley

Level 3 Expert

513 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...