Question about Suzuki 2004 Twin Peaks 700 4X4

1 Answer

Makes a squeeling noise after acceleration

Makes a loud squeal after acceleration and sometimes when you shut the engine off

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 500 questions.

  • Suzuki Expert
  • 578 Answers

Starter throwout bearing or squirrel caught in chain

Posted on Apr 18, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

'93 Polaris 350l 4x4. What are the symptoms of a broken piston skirt?

severe knock / rattle under load
excessive smoke as the crack normally occurs at the oil ring groove dropping that ring into the sump
describe the symptoms that you have as if it is a rattle under acceleration that will be detonation and is a air/fuel mixture problem or ignition timing too far advanced the skirt is what maintains the alignment of the piston crown so if it is cracked /broken off you will have no doubt of the noise at idle and at rpms
pistons seldom fail because of the engineering and material used so it would have to be an extreme operation that would cause the failure
other similar noises can be from loose valve seat insert
piston hitting valve head from failed valve spring big end bearing cam lobe worn out

Dec 12, 2017 | ATVs

2 Answers

2009 Ranger 500efi. I changed starter and starter Bendix. It's like something not releasing after it starts, I shut it of and it still turns over. Sometimes after it starts it's got a odd noise

Turn over is the process that an engine makes when it is trying to start. If you twist the key and get nothing then it wont turn over. Google shimming a starter and watch the vids.

Feb 18, 2017 | Polaris ATV

1 Answer

I have a 1993 Artic cat jag 440 that wont stay running after it warns up. What could be the problem?

Check the insulation under the gas tank. Sometimes if this is worn or falls off, the heat from the engine heats up the fuel which causes the fuel pump to act erratic, even stop working. Also make sure you have the correct heat level spark plug installed. If it's at the wrong heat spectrum, it will stop functioning and shut down.

Nov 20, 2016 | ATVs

1 Answer

Loud squealing noise if you run slow,if you speed up it goes away

most likely, the primary clutch is faulty and requires repair or replacement.
Weight, Shift ? 14 ?Asm., Roller and Bushing

Apr 21, 2016 | Polaris 2015 Ranger XP 900 EPS Hunter...

1 Answer

Econ Quad Viper 70 4 stroke won't stay running unless choke is one quarter or more closed. Occasionally pops through carb and bogs down if accelerated.

Hi Linda... Clogged carb jets and be a problem. Cleaning them is often very difficult due to the size of the orifice. sometimes welding tip cleaners or sewing needles may work. Forcing air is a good way but the acid test is to look into the orifice to verify you see light.

Another thought: Sometimes the fuel caps stops venting and the motor will act like its running out of power, rightfully so as it's running out of fuel. The vent in the fuel cap can be partially plugged or completely and the engine will act accordingly. Best way to test this is to remove the fuel line after the petcock(off/on valve) and watch that it flows fuel well. Also check the petcock filter to verify it's not clogged and check the fuel line to make sure it's not crimped.

You're problem doesn't sound electrical but I'd try to eliminate all fuel related problems first before moving to electrical as electrical trouble shooting can be a bear.

The air mixture adj screw sometimes has an "O" ring and sometimes not. Check with parts fiche for your model carb to know which.

Dec 21, 2014 | ATVs

1 Answer

Why does my Yamaha grizzly 700 engine brake fail going down hill

If you're in to low a gear, the clutch might be slipping under stress from high revs. You might need a new clutch or stronger springs. Try using a higher gear and use 50% braking.

Jun 21, 2014 | Yamaha 2007 Grizzly 700 FI 4x4 Auto...

1 Answer

Squealing noise with tao tao atv

when you rev or when you're in motion? need more info

Jan 01, 2014 | ATVs

1 Answer

Four wheeler

Could be a CV axle if worse when turning tight it's a front sounds like a rear tho.

Aug 27, 2013 | ATVs

2 Answers

1989 yamaha blaster does not stay on

mcdevito75 here, Sounds like a lack of spark to the spark plugs to me, have a shop check it out for you, menwhlie you can check all around your Yamaha blaster for any wires loose or not connected.

May 24, 2010 | RTO 200cc Full Size Four Wheeler ATV

Not finding what you are looking for?
Suzuki 2004 Twin Peaks 700 4X4 Logo

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki ATVs Experts


Level 3 Expert

78289 Answers

Lawrence Oravetz

Level 3 Expert

10137 Answers

Brent Tischer

Level 1 Expert

26 Answers

Are you a Suzuki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides