Question about Polaris 2013 Sportsman XP 850 HO EPS

1 Answer

New 3weeks old transmission sounds like it has slack in it when you put in rev. it makes a clack noise when slack catches up , and when you go forward same thing when you let off throttle and get back on the throttle ,it will make the clack noise like there is slack somewhere in drive train

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 102 Answers

Sounds like a bad U joint.

Posted on Jan 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

STARTS IDLES BUT WONT REV UP,ALREADY CLEANED CARB ANY OTHER SUG


You cleaned the carb; did you rebuild it? Did you put in new throttle springs and adjust the needle jet properly... the keeper ring placed on the correct groove? Did you put a new float in and then adjust the float travel properly? If you didn't do these things, then you aren't finished yet. All these things make a difference. If you need to put a new float in, be careful as the metal tab is easy to break off when bending it to correct specs.

Mar 05, 2015 | ATVs

1 Answer

My quad has no power in reverse what can the problem be? i changed the angle sensor and reset the computer.


dont know but computer ,shouldnt matter motor runs 1 way ,make sure its fully in rev , check wire to rev solenoid if it has one ,sory im not familiar with this ,let us know i think it might have a limiter when in rev ,you know how hard and complicating they are now days,and call it for safety.

Sep 25, 2014 | Honda 2009 FourTrax Foreman Rubicon...

1 Answer

Olaris sportsman 800 epi AWD...an it has been


Hey Anon,
This sounds very serious..Unless you are a VERY GOOD mechanic, you need to take this machine to a qualified professional..it will be best in the long run...

Jun 25, 2017 | Polaris ATV

1 Answer

Tips on how to free up a tight bottom end on a 08 kfx450r not locked up will still run with a roll start but to tight to start of the starter? headgasket did blow and got a lot of water in the oil and got...


change oil ? water wont compress!!! prolly gallded all internal parts . at this point i would try transmission fluid. drain oil and check for metal or allum. shavings. refill w/trans fluid , remove spark plug , add tfluid in very small amt to cyl. replace plug.start briefly dont rev eng at all . let idle if it will. maybe 1 to 2 mins. shut off let complete cool down . restart again w/same fluid. same as b4. stop drain fluid . smell t.fluid if burnt or not. flush cranckcase w/new oil. hope for the best here. refill eng to proper level and p++ y. has worked for me but wasnt severe as yours sounds to be. good luck let me know if it helps or not. be sure ALL TRANS FLUID IS GONE FROM ENG. B4 new oil is put in . replace oil filter too b4 trans fluid is added and after tfluid is emptied.

Jul 14, 2014 | ATVs

1 Answer

Why does my Yamaha grizzly 700 engine brake fail going down hill


If you're in to low a gear, the clutch might be slipping under stress from high revs. You might need a new clutch or stronger springs. Try using a higher gear and use 50% braking.

Jun 21, 2014 | Yamaha 2007 Grizzly 700 FI 4x4 Auto...

1 Answer

Yamaha yfm200 gear problems


Hey David,
You knew this and bought it anyway..??? No it cannot be something simple.. its going to cost $$$.$$.. get ready... I would definitely weigh the costs verses the value when done... its probably not worth the $500 - $700 dollars a transmission/clutch complete rebuild will cost..??? .. try selling it for parts or trade it in on something new!!

Jun 20, 2017 | ATVs

1 Answer

Clutch belt is slipping in the forward gears.wont move forward


can you loosen the alternator to tighten the belt? If so tighten to about 1/2" slack, if not may need to replace the belt.

Mar 16, 2014 | ATVs

1 Answer

Clutch does not engage at low rpm and causes machine to lunge severely


Sounds like the clutch weights are sticking
here are the service manuals for all Arctic cat ATVs

Parts House Lawn Mower Parts and Chain Saw Trimmer Parts

Mar 01, 2014 | Arctic Cat 2009 400 H1 TRV 4x4

1 Answer

2005 sportsman noise in the rear area of the machine


The belt and pulleys are probably not the cause with the sound you are describing. To me it sounds more mechanical when you say grinding. Have you checked the rear dif?

Mar 17, 2017 | Polaris ATV

Not finding what you are looking for?
Polaris 2013 Sportsman XP 850 HO EPS Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

john h

Level 3 Expert

12650 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Wade Mobley
Wade Mobley

Level 3 Expert

475 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...