Question about kawasaki 2004 KFX 700 V Force

1 Answer

Fuel pump not working

Wiring?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Try the relay (and fuse) you could take the fuel pump out and wire it to a battery pos and neg just to test it out

Posted on Nov 18, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the wires needed to hot wire a kfx 400


When you "hot wire" an ATV with a battery is the same as leaving the key on 24-7. This is not recommended..A good locksmith might be able to help you resolve your "switch issue"
BUT.. the brown wire and the gray wire(both are ignition switch wires).. connect them and you should have power

Oct 15, 2016 | kawasaki 2004 KFX 400

1 Answer

Is there a free wiring diagram that show what wire to connect my new winch to


Red is POSITIVE.
Connect to + terminal of battery.
Your winch should be equipped with a fuse.
Do not connect to any of your wiring except battery side of solenoid PROVIDED wire is same gauge or bigger (thickness) than winch wire.
Connect Black to frame or negative battery terminal.

Jan 20, 2016 | Suzuki 2009 KingQuad 450 AXi 4X4 Limited

1 Answer

2007 Polaris sportsman 700 EFI and am trying to install a superwinch t2000 on it. I have the winch on already but my problem is it had one on that was wrecked and the switch was gone. My question is on the...


This winch should simple straight foward hook up. Your big red & black wires should hook straight to your battery. Red (+) black (-) if there is no fuse on the wires put at least a 20 amp.fuse close to your battery. These are the main power suply. They will go in a.small black box. Also coming out of the black box will be the wires that run to the cable in & out switch.and there should be one heavy ga. Wire going to the winch motor. Make sure the wire is good and clean when you hook it to the winch motor. Do not over tighten the nut . Just give a good snuging down. As for your solenoid box. That should be the little black box that your main power wires go into and controle wires come out of..

Nov 23, 2014 | ATVs

2 Answers

Atv wiring diagrams


does it have 4 or 5 wire cdi box . pretty basic but need to know which cdi box it has. help me help you !

Jul 14, 2014 | ATVs

1 Answer

Service codes for 03-04 polaris 700 twin


Here is the lowdown on Polaris Sportsman 700-800 T-Bap wiring:

Symptoms of broken Temp/Baro sensor wires:
1. The ATV will run very erratic at idle.
2. The "CHECK ENGINE" will sometimes come on.
3. Diagnostic codes 41 and or 45 will be present.
4. Fuel mileage will be poor.
5. Exhaust will smell really rich. Sometimes even black smoke can be seen from it running so rich.

How to test if the Temp/Baro sensor wiring is broken:
1. Turn the key switch on and off 3 times leaving it on the 3rd time. This puts the ECU into diagnostic mode. If codes are present their numbers will be displayed on the instrument cluster. When all codes have been displayed "End" will appear on the cluster.
2. Remove the seat and locate the sensor on the air intake tube. Unplug the wiring to the sensor by pressing down on the tab on the top of the connector. DON'T PULL THE CONNECTOR BY IT'S WIRES!!! Pull back the vinyl tubing that covers the 4 wires going to the connector. Gently pull on each wire with your fingers. The wire should have no stretch and feel solid. All the wires should feel the same. If one or two of them feel weak and stretchy chances are you have a broken wire. Is what happens is the wire breaks inside the insulation so it appears to still be connected.

Why do the Temp/Baro sensor wires break in the first place?
1.The problem with the current Polaris wiring is too short and Polaris used 7/32 stranded 22AWG wire. This wire has a very low strand count and should not be used in applications where vibration occurs.
2.The next problem is the mounting location of the sensor it is in a vibration prone spot on top the air intake tube going from the air box to the throttle body. Next time you're bored take the seat off and rev it up in neutral. That intake boot and sensor vibrate to the point where it looks blurry. The combination of these engineering flaws causes the cable to break in a big hurry.

The Polaris repair kits keep breaking. Why?
1. The replacement kits from Polaris use the same 7/32 strand wire that can't withstand vibration.

find a heavy duty one on the internet or ebay................

May 29, 2014 | ATVs

1 Answer

Taotao atv ata-125d wiring diagram


well if your wires fried then your battery was around 20v which means your voltage regulator was bad. you need to purchase a new one of those as well. as for the wiring diagram, if the wires around the battery had been fried. are they intact or completely burnt without you being able to locate to which each wire connects to?

Aug 14, 2013 | ATVs

1 Answer

4wheeldrive wont go off. only have power to motor when 4wheel drive is activated. have no reverse polarity to disangage 4wheel drive. found motor wire wore through to frame blowing fuse causing quad to...


one of your repaired wires is not getting power or ground.. Recheck your wires,.
And most likely look farther up the wire loom for burned threw wires..

Nov 23, 2017 | Suzuki 2005 KingQuad 700 4X4

2 Answers

How to wire a coil on a 4 wheeler


1 thin wire in, one big fat wire to the spark plug. its not rocket science.

Mar 09, 2010 | RTO 200cc Full Size Four Wheeler ATV

Not finding what you are looking for?
kawasaki 2004 KFX 700 V Force Logo

Related Topics:

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki ATVs Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Lawrence Oravetz

Level 3 Expert

9783 Answers

Glenn Smart
Glenn Smart

Level 3 Expert

818 Answers

Are you a kawasaki ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...